Hey.
I have a problem where the task watchdog times out immediately.
I have taken the samples/basic/task_wdt sample and modified it a bit to simulate what I have in...
Hi!
First off: I know the Cryptocell register interface is not officially supported, but I'm using it for learning purposes and I'd like to understand what's happening....
Hi Nordic team.
I have an issue performing the "Bluetooth Throughput" test using the suggested "Bluetooth Throughput example".
I have created a new application using NRF...
I was messing around with my nrf52832DK and set it to boot mode now the LED5 is flashing continuously, I've tried uploading JLINK firmware into the boot device folder but...
Hello, We want to build our own custom protocol because the features we need are not available from existing protocols like BLE or Zigbee etc. But it is beyond our reach to...
Hi everybody I'm using nRF Connect SDK 2.6.1. I have my own board based on nRF52840 SoC. I made an overlay file of nRF52840DK and changed its UART TX/RX settings according...
Dear Nordic Semiconductor Team,
I am interested in obtaining the datasheet for the nRF54H20 chip. Additionally, I would like to inquire if it is possible to implement Classic...
Hello,
once synchronized, what is the minimum time for exchanging acknowledged packet.
according to datasheet :
Timeslot periods
The Gazell Link Layer supports...
I've setup Eclipse GCC tools for building and debugging as per the nAN-29 app note (and lot of online help) and able to build the code. However, the debugging is working only...
I'm new in nordic.
I want to use nRF51822 as an iBeacon for iOS.
This is possible?
There is an example, documentation for this ?
I have nRF51822 BLUTOOTH SMART BEACON...
I'm interested in working off the reference design for the nrf51822 to create my own board. I have a few questions about the 3 inductors specified on the schematic/BOM: ...
hi,
I an trying to enable notification from server. According to spec. i have to write 0x01 to the CCCD handle in heart rate characteristic in ble_app_hrs. In the BLE_GATTS_EVT_WRITE...
hi everyone
(1) everytime,the pstorage_init get the same block id, if we wrtie it more than 20,000 times , will this block become a bad one? if it will, can the program automatically...
Hi, Ole
I am using Nordic development board with Nordic dongle to communicate,..but I am getting receive link loss. I have removed reset from error handler, though the...
I have a setup where I will be switching the nRF51822 UART between two different peripherals (one being a connection to another nRF51822), so I need to be able to safely close...
Folks,
Sorry if I'm just being boneheaded here, but have been fighting with a couple problems while migrating my app on nRF51822/"C0"/SDK 4.2.2/S110 5 to nRF51822/"G0"...
We have made a custom board using nRF51822 connected to a MPU6050 accelerometer running on a battery.
Currently, we have issues performing reset on the chip. We have to...
Hi
I'm trying to measure the frequency of a pulse signal that runs at a moderate pace, varying between 50 and 500Hz while the SoftDevice is active. The softdevice needs...
Hi all,
I am having a bit of a problem with the printf. I could not figure out what could be the problem. From what I search people seem to be getting it working with out...
hi....
how can i implement bonding in app_ble_hrs example code from SDK V6.1.0 with soft device V7.0.0. the bonding should be done with a pass key.
can any one help...
Tried V5 a few months ago. But Nordic Semi didn't support their devices at that time.
I installed V5 today, and found a bunch of goodies :-), even including a nRF-RTX! ...
Hi
We did a few tests with the S120 softdevice (example in the SDK 5.1). Most things are working as expected, but the range of the device is by far less than we reached with...