So whatever I try, the only way to get my idle current consumption to an acceptable low value is to set CONFIG_SERIAL=n in my configuration. But then I don't get printk functionality...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
Hello,
I tried to use the Cellular Monitor app within the nRF Connect for Desktop software, but it encountered the following error. I have included the relevant part of...
How can we connect the Thingy:53 to the PPK2 using the included PCA64142 current measurement board, for both Source Meter and Ampere Meter modes?
The PCA64142 board...
Hi,
I have a Thingy:91X which connects fine to hello.nrcloud.com. Now I want to connect it to my own nRF Cloud account.
Note that I have successfully provisioned multiple...
Hello,
Recently, my team has been struggling with an issue regarding a nRF5340 device that's encapsulated and inaccessible to be flashed with a JTAG connection. Our normal...
Hello,
I’m currently working on a Bluetooth Mesh project using Nordic Semiconductor devices, and I would like to get guidance on static provisioning and group-based communication...
I am using an Arduino and NRF8001 break out board from Adafruit. I am using the UART profile (adafruit sample code) to send data between mobile phone and Arduino. However...
Hi,
I am trying to setup the nrf8001 by sending the setup commands from my microcontroller. After I send the complete setup packet (21 commands) I receive, as expected...
I'm working on integrating nrf8001 with STM32, currently trying to write my own stack.
Upon reset, I read the DeviceStartedEvent, 0x81 and it shows "0x02 0x00 0x02", which...
After a fresh install of Keil (along with Legacy patches) and the SDK, I get the following messages when I try to open the ble_app_template_s110 project:
The project...
Hi All,
I use iot_ipv6_udp_client example on nRF51 DK.
I modified it and send data in one direction only (not receiving back).
Testing has shown that the maximum packet...
Hello,
I use S130 with NUS style connections as central and device at same time. It works nice and performance is good but when i run scan, performance become very poor...
Hi,
I'm using S130 with SDK 9.0.0 and as central, I'd like to read values for more than one characteristic on a peripheral. I do so in BLE_GATTC_EVT_CHAR_DISC_RSP by firing...
Hi,everybody!
Recently,i use nrf51422 as peripheral programming s310 ant_ble_hrs example in sdk6.0 and use nrf51822 As center programming s210 hrs example in sdk6.0. I find...
Suppose I have a lot of very small characteristics (1 or 2 bytes) to send lots of notifications on. They are all updated simultaneously, though the central doesn't care about...
It seems daft, but the ble_heart_rate_template_with_battery_service example in the nRF8001 Arduino SDK does not use the nRF8001's Battery Monitor!!
Instead, it just uses...
I'm working on an application that uses the persistent storage manager to store some calibration data. I thought I had everything working well, but after higher volume testing...
Hi,
I have already developed (and almost finished) an application with SDK 8.1.1
As you now when I created the application starting from an SDK example, the project under...
Confirm all the certifications the product nRF8001 is currently holding (or in the process to be awarded).
Is the nRF8001 certified/approved to be commercially used in...
Hi there,
As per title, the Ble bandwidth test on my Blend Micro is not connecting to the nRF UART app on iOS 8. I tap connect and it just says 'scanning....'. Could you...
