Hi,
why antenna trace is connected to mounting pad instead of feeding pad of antenna in thingy 91x
We are designing our device based on this. We wish to be sure about...
I've been trying to flash an nRF52840-DK with code that successfully builds on Segger. The Segger error is "Failed to connect to target." I updated the devkit firmware with...
I am trying to set up a w25q128 using SPI with a nrf5340 on a custom board and had a few questions. I have used DevAcademy as a reference as I do eventually want to set up...
I have a custom board with nRF52840. It draws power over USB and the data lines are connected as well
USB is defined as follows in the dts
cdc_acm_uart0: cdc_acm_uart0...
Im tring to generate sbom in html or spdx format yousing west ncs-sbom -d build i got this error: package.name += '-' + package.version TypeError: unsupported operand type...
Hi there, I'm facing difficulties configuring the Adafruit ILI9341 with the nRF52840. Are there any beginner-friendly instructions on how to configure and program it over...
Hi,
I have two nearly identical revisions of a board with an nrf5340 which behave differently in a curious way:
On one revision I can issue a "mon reset" command in...
Hii all,
I wanted to generate a clock pulse from the pin P0.05, I've written the code and when I tested the application with nrf51 DK with chip 51422-AC its working fine...
Hey everyone,
I'm trying to send a value as a notification packet from GATT Server (slave) to GATT client (master) at 7.5 ms connection interval. I have set up the radio...
I am using a simple 4 by 4 matrixed keypad, and I would like to handle some of the decoding myself.
In essence, I would like to configure all 4 rows as low driven output...
Hello,
I already searched the forum, but I didn't find anything.
Is there a way to invert a port on a NRF51822?
I use this chip together with an XMega-Chip and they...
Hi,
I'm trying to get PCA10001 board working. I used ble_app_hrs example from SDK 6.1.0 (I'm using eclipse with gcc). The Softdevice is v7.1.0
The application seems...
I have a nRF51DK with SD 8.0 flashed.
I would like to start and stop a pwm signal with the buttons on the board(BUTTON_1 and BUTTON_2). The pwm is working fine. But when...
Hello:
I want develop my nrf51822 project base on new sdk and softdevice.In /nRF_Examples/9.0.0/ble_periphera/ble_app_uart/, the keil project device is nrf51422,and it can...
Hi,
I'm compiling the simple blinky example with no softdevice for an NRF51822 xxAA using GCC on linux. I can't get any LEDS to blink off the GPIOs, so I'm debugging with...
I can see a phrase "Not recommended " on the Evaluation Kit's page: www.nordicsemi.com/.../nRF51822-Evaluation-Kit
What could that mean for me if I already have the kit...
I found in ble_app_uart example, any device with UART app can connect to uart service and send something to COM port or just block the connection of other devices.
So can...
I'm trying to update my firmware using the dfu, I tested two examples of the SDK :
one of them is dfu_dual_bank_ble project,
I noticed that the memory allocation...
Hello,
I have been reading a lot of Nordic and DevZone stuff. The information I need appears to (almost) be there but I cannot quite put it all together. I need some help...
Hello, I am asking for your help again.
I just managed to brick the chip that I am working with. The problem is that I am not able to erase or program the flash. However...
Hello,
I have not found a lot of information on connection encryption. I want to use a preprogrammed Long Term Key in my mesh that is then used to establish subsequent...
This is the application file I am trying to download:
dx02.zip
This is the sniffer Log I just captured by wireshark
dx02_20150820.pcapng
I was able to upgrade firmware...
