Hi,
I am using nrf52832dk board for test nus service with ncs2.9.0, but I am facing some problem with MTU setting.
I found a configuration item "
CONFIG_BT_L2CAP_TX_MTU...
Hi,
We have some GPIO pins where we want to change their configuration during runtime. We want to switch them between input pull down and output. Is this possible?
When...
Hello, we are developing a BLE application using nRf52833. Because of the waterproof & stainless steel casing requirement with rechargeable battery charging capability, we...
Hi team, According to this statement, it indicates that access port protection can be deactivated by modifying the TAMPC.PROTECT registers, which can be achieved by executing...
We are currently implementing the 9151 SIP into our design, and we am noticing some discrepancies between the datasheet and the evkit schematic. I am hoping you can help us...
Trying to set up a PPK(II) to measure the current in my nRF 52833-DK and preparing my nRF Connect for desktop to do so, I notice that this tool is demanding a V7.94i version...
Hello,
I am working with the NRF5340dk, nrf7002ek, and PPKII. I am unable to get the DK to power up with the PPK. I used a knife to break the trace but for some reason...
I am using nrf51822 with PCA 10001, SoftDevice S110 8.0.1. I try to compile the example "ble_app_proximity_s110_pca10028" and after I made a connection the device disconnects...
Has anybody had any experience in programming an nRF beacon kit over the air using the built-in Bluetooth Smart interface in a Windoze 8 laptop? (HP 255 G3) Is this even possible...
Hi,
I wanted to create fixed rate waveform. I first used nrf_delay_us with nrf_gpio_pin_toggle. But I realized it is not accurate enough to do it, especially when the device...
Hello,
I'd like to know how exactly do i implement this function in my app?
I tried getting the value from response (as shown in documentation) : ble_gattc_evt_char_val_by_uuid_read_rsp_t...
Hi,
My Jlink lite CortexM work with nrf51822 DK boards. But my PCB with nrf51822_xxAA chip can't download code. I'm using ukeil
When I chek in utilities Jlink can't recognize...
I am initializing an SPI master to talk to ADXL362 accelerometer using NRF51-DK.
Datasheet page 19: www.analog.com/.../ADXL362.pdf
No matter what I do connected or disconnected...
Hello,
I am new to working with imbedded chips and could use some help. I am working with a pre-programed nRF51822 chip on a PCB and would like to be able to read the imbedded...
Hi I want to using nRF51822 link with MCU ti-am335x have Linux system(Ubuntu) by standard HCI command, BlueZ or related hci tool.
I know that I can use nRF51822 S120 serialization...
I would like to share my wireshark capture file (pcapng) with another developer to view that doesn't have a nordic sniffer. They cannot see the ble protocol information. Is...
I am able to set the connection timeout to 250ms in the ble_app_hrs peripheral sample, but in the ble_app_multilink_peripheral it will not advertise if I set it below 1000ms...
Hello,
When using the bootloader I've noticed that the booatloder resets after advertising for ~1minute. I'm try to figure out if this is intentional.
I notice that...
Hello,
I am currently designing a project that will advertise as two different beacons simultaneously using the Timeslot API. I have successfully implemented the nRF51...
In my all projects, I am using this code to obtain and set local device address:
uint64_t deviceId = ((uint64_t)NRF_FICR->DEVICEID[1] << 32) | ((uint64_t)NRF_FICR->DEVICEID...
Hello,
I build a Broadcaster(iBeacon) with the DK PCA10028. This Broadcaster sends periodically ervery 30ms a message (I have sniffed the Broadcast message and it appears...
