Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hello,
I know that this question was here before, but I've read all of the questions and answers and still I don't know what I do wrong.
I'm using 3 PWM channels to...
Hi
While browsing the new files in the SDK 8.0.0 i had a look in the new ble_advertising module. In the start advertising function the pstorage access is checked if it's...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I have the nRF8001 plugged into the shield for the Arduino Uno.
From the Arduino SDK from Nordic, I have downloaded the BLE Hello World program to the Arduino, which should...
I know the SDK lists it for the S110 stack:
http://developer.nordicsemi.com/nRF51_SDK/doc/7.2.0/s110/html/a00066.html#app_dfu_intro_sec
But trying to use it with the...
There is a GitHub example:
https://github.com/NordicSemiconductor/nrf51-dfu-ble-S130
It states that the SDK 6.1 is required. Will it work with the 7.2 SDK using the...
I am trying to use TIMER1, but it seems that my ISR isn't being linked in during the build.
uint32_t timer1_init(void)
{
...
NVIC_SetPriority(TIMER1_IRQn, APP_IRQ_PRIORITY_LOW...
Hi,
I'm developing beacon-scanner software using nrf51822 and S120 softdevice.
Using softdevice v1.0.1.
I need to scan ibeacon type advertising devices and get service...
I am currently trying to come up with a viable strategy to log error codes that arise while my device is being used in the field. When an unexpected error code arises, I would...
Does someone use it?
The gls example from SDK 7.2.0 with softdevice 7.1.0 works.
However, the gls example from SDK 8.0.0 with softdevice 8.0.0 does not work.
I am using...
Hello, I'm new to bluetooth system.
I want to make some H/W device which using with sensor, MCU and Bluetooth.
Very simple, MCU control the sensor and get the data,...
Hello,
I have questions about DC/DC setup in nRF51822.
Is there any automatic switching between DC/DC enable and disable along with battery voltage except DCDCEN...
