I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Is there an AT command (For modem firmware >= 2.0.2) that can be used to validate whether the LTE modem can communicate with an external MIPI RFFE switch (for example on a...
Can Nordic share specific instructions on how to enable hardware tracing?
I've received the following patch from Tomasz, however I still see "trace clock missing" in Ozone...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
hii....
am working on a custom profile having broadcast feature in active connection... am advertising some sensor readings and scan response and a battery service before...
Keil uVision 5. SDK 7, SD310 Version 2, PCA10028 board
I'm NEW to ANT. I have running ble_ant_app_hrm example. The code compiles with no errors or warnings, loads, and...
Please help: Debug is mentioned in many places and is of several types (uart, ble, assert...). I need clarification to distinguish which debug type is in effect, and how to...
I have a project based on ble_app_lbs example. When I started the project I was using the S110 stack and SDK 6.1. I have much of my BLE code working, but the project has expanded...
It seems to be the case that pstorage_write errors (for example forgetting that it needs to be word-alignment, so 4 bytes at minimum), do not end up in the pstorage_callback_handler...
Hi there
I have never used a nRF51822 device but it looks like a good option for a product development.
Reliability of the link is a priority so the design will include...
I want to connect Bluetooth Smart chip to a weighting scale, read the data and send it to a phone.
Is this possible and what requirements there are for the scale?
The Manual of the nRF518-SDK version 5.1.0 mentions something called nrfprog. Unfortunately the SDK doesn't include it. Unlike what i found on google, i see no nrfprog in...
I have an nRF51822 design that programs fine from the embedded Segger on the eval board.
However, when I try to connect an actual J-Link Base, I can't seem to get it to...
Hi
I have PCA10005 module disassembled from mother board and with VCC_nrf, GND connected to external supply. The chip is able to work with pre-programmed data.
Is anyone...
Hi,
i have a generell question. First i have to say i am not the best programmer, but maybe some one with more experience then me could help me.
Does it make sense to...
Got nRF51422-EK.
Followed instructions and used nRF51 SDK v6.1.0
LED next to the Segger part blinks constantly.
If i build and download Blinky, the LED0/1 do not alternate...
I am developing a platform using C8051F931, MPU9150 and nRF8001. I have re-written the hal code to target the C8051F931 and verified it using the ACI demo test (the echo test...
Hi,
I'm using nrf51822, pca10001 board. I have loaded the uart_example and that worked fine, but using the radio_test_example from Board/nrf6310, that compiled and programmed...
Hello,
I'm new to BLE. I am using nRF51822. Is it possible to modify calling frequency of nus_data_handler() so that I can deal with data coming from BLE faster?
How can...
