Hi there, I am unable to install an SDK through VSCode while trying to take the steps outlined in the documentation. I have navigated to "Manage SDKs" under the "nRF Connect...
Hi,
I have a problem with nRF52832 after entering the radio RX state. I use a proprietary protocol with fixed packet length. Packet transmission works fine, receiving the...
I am working on a wearable GPS tracking device using the nRF9151 DK and testing the GNSS example code. However, I am facing an issue with the cold start time for acquiring...
Hey everyone,
I have designed a custom board with a bunch of nordic IC's (nRF54L15, nRF9151, nRF7002 & nPM1300)
I have tested the basic functionality so far, including...
How can I display the nrf serial terminal logs files on VS Code while keeping the same colors and text highlights for dbg , inf , wrn , etc., just like when viewing live logs...
Hi,
I am trying to build bluetooth hci_uart sample for esp32 board and haven't had much success so far. I am running this command to build:
`west build -p always -b...
I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
Suppose I want my BT peripheral to provide Measured value of sensor X and Location of sensor.
Currently I have to send the following attributes
Service Attrinbute
Characteristic...
Hi All,
I am working a custom board for 51822. We have wired the UART RX/TX pins to a microusb connector (No RXD/TXD pins wired). The problem is once we connect it to PC...
Hello,
all was working fine, until today.
When I plug my dongle, my computer does not react.
The green light on the dongle is off.
Even if I suppose that it's a...
For my current project, I need to compile the »over the air bootloader« with gcc (because our buildserver runs on linux, developers using Mac … no Windows and no Keil so far...
Hello, I want to get Pwm output using softdevice but i am not getting it.Here is my code attached main.c please tell me where i am going wrong.Do ineed to initialize softdevice...
I am looking at using the nRF51822 in an application to create an Ethernet gateway and want to be able to download new firmware to the nRF51822 from a remote server. I plan...
I have an nRF51822 application using the Soft Device 110. I want to perform bonding with a central without MITM protection. In my on_ble_evt() event handler, when the event...
Hi,
I am new to the scene of BLE beacon development. I am using multiple Bluetooth smart beacon kits for indoor ranging/positioning purposes. To reduce the effect of interference...
Hi,
For S110 6.0.0 we use such script to split hex to binary. But it seems 7.0.0 is changed and current way is not working anymore.
Convert from hex to binary. Split...
Hi
I am writing my own bonding manager.
In the S110 stack after Phase 3 of pairing the keys are exchanged which result in the EVT_AUTH_STATUS event which in turn contains...
when I add my own service and add characteristic, a odd phenomenon confuse me.
When I set cccd_md.write_perm:
BLE_GAP_CONN_SEC_MODE_SET_OPEN(&cccd_md.write_perm);
...
after several attempts to debug and understand what goes in my handlers in the BLE callbacks, I thought to give a UART logger a try.
this is what I'm trying to use: OpenLog...
Hello,
I am looking for a not expensive way to program nRF51822 by frame of 10 modules. All the 10 modules would be connected to a PC using pogo pins, and I would use a...
I can get an information that bluetooth smart connects bluetooth smart ready.
But I can't get an information that bluetooth smart connect bluetooth smart ready.
So, Would...
