Hello,
I am working on an update of older FW implementation: nRF52832, SDK 14.1.0, with SoftDevice S132 and using BLE connection.
The change I need to implement is a functionality...
Dear Nordic-support,
I am trying to use the modem_battery_low_level_handler and modem_battery_low_level_set(), but I think there are two different ranges for the battery...
Hi,
I am using an nPM1300 together with an nRF5340 and an LIS2DW12 accelerometer. The nRF is powered from VOUT1 on the PMIC, and after some time of inactivity it is turned...
Hii,
Downloaded Timer code from sample and trying to build using 2.9.0 SDK but not able to build. It is building using 2.6.2 sdk.
Pls check and update soon.
Thanks...
I'm looking for an nrfutil command to replace this command:
nrfjprog --memwr 0x10001080 --val 0x12345678
My goal is to write a serial number to the UICR CUSTOMER[0] register...
Hello,
Our company makes module using nRF52840. And we also make development kit with it.
I recently programmed open bootloader built-in hex in nRF5 SDK v17.1.0 (examples...
I created my first nRF52832 (QFN) layout including PCB antenna. Before I order the PCBA, I would like a review. My design is almost identical to the reference schematic for...
Dear Sir,
After I remark this //BLE_GAP_CONN_SEC_MODE_SET_OPEN(&cccd_md.write_perm); and program it into nRF51822, then I cannot program it again. PC program report it...
I have modified the included HID mouse example to allow for left/right/middle mouse clicks. However, it is not clear to me how to set an event handler for both when a button...
What is the recommended PCB thickness of the nRF51822-QFAA Reference Layout? It'd be great to have a specification in the package including the full spec of the PCB material...
Hello Folks, I'm starting some work with the nRF51822 Evaluation Kit (PCA10001), but have very quickly run into a blocker when trying one of the ble samples. (I've previously...
With Soft Device 5.1.0 I generated the binaries from the hex by doing:
arm-none-eabi-objcopy -Iihex -Obinary --remove-section .sec1 --remove-section .sec2 s110_nrf51822_5...
Dear support,
We are in the design stage for a BLE application. We looked at different options. Although the NRF51822 seems better in specs. The TI parts CCxx offer this...
So far I have made a successful program that utilizes BLE to send and receive radio signals in Kiel. But I have only been testing this program by using the provided Master...
I just entered a Case to Nordic with this same question but do not expect to get a response over the weekend so I am posting here. I made the assumption that the Nordic Cases...
Dear everyone:
Now,I have a project which use Nordic product solution to developemnt.
And , We need your company to provide some information and solution.
(like,have...
What is the maximum value of RSSI parameter for nrf_gzll_device_tx_info_t structure?
I have done a test on RSSI parameter value return in nrf_gzll_device_tx_success callback...
Hi Nordic
I don't fully understand the drive settings for the GPIO. For example S0H1 means when the pin is CLEARED, it will use standard drive (can sink 0.5mA) and when...
Hi there,
i was trying to implement a firmware for a small device using the nRF8001 only in broadcasting mode.
So far, everything works fine. But one thing mentioned...
I'm happy with the status of my app on the evaluation board and I'm ready to start downloading it to my target board. I plugged the Segger J-Link Lite CortexM board into one...
