Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi !
On this thread devzone.nordicsemi.com/.../nrf51922-1 i've found someone introducing the new S130 softdevice for the nRF51822 wich allows the IC to be on concurrent...
Hi to all,
Ihave a problem with erasing flash on nRF51422 Evaluation Kit. When i click on Erase all button in nRFGo Studio everything is looking normal ( segger led is blinking...
I cannot download S110 to try right now. I have some 51822 Dev kits, but somehow I didn't get the product keys entered into my page, and the boxes are all gone.:D
When my application is running on the nRF51822 (e.g. the hrs example from the sdk), I want to stop this application (e.g. at a breakpoint), investigate some memory and than...
Hi,
I've started developing some test applications for the nRF8001 to better understand all the ACI libraries and improve my knowledge of the chip.
I'm experiencing some...
Unless manually set the value of bond_init_data.bonds_delete to true in the function bond_manager_init to clear bonded masters, I end up in the HardFault_handler. The last...
I'm trying to just set up a Timer for 8 MHz frequency and have that output on a pin. It seems simple but I'm having some problems (the frequency is a lot lower). What am I...
Hi everyone,
I've just started to develop software for NRF51822 - Bluetooth Low Energy on the Evaluation Kit. I managed to connect the development dongle and evaluation...
Based s110_nrf51822_5.2.1_softdevice.hex and nRF51 SDK v. 4.4.1
When scanning iOS, why not click pair on the iOS side and NRF51822
connected on? whether the pair can be...
Hi,
I'm planning a hardware solution and I need a BLE IC capable of act as a master and a slave, not at the same time, but with the possibility to change it's role by software...
I used nrf8001 to implement ANCS.It working fine.But when it disconnect for a while and reconnect(reconnect successed).I found Iphone can't send any ANCS message to nrf8001...
Hi, I would like simplify the nRF24AP2-8CH signal RF output using a Balun with a chip antenna.
What is the best way: the 2450BM14A0002 from Johanson, the BAL-NRF01D3 from...