Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
I have two computers where nRF Connect for VSCode behaves differently in the sense that in one computer when I start debug it stops at the first line of the main and I see...
Hi,
I've integrated the softsim feature to the modem_shell application, which is working fine.
But I have a performance issue: I'm receiving the APDU from the modem...
Hello Everyone,
I am using NRF52811 evaluation board for my development purpose using SDK 2.6.1 on visual studio code.
My tasks involve LED control using Bluetooth as...
Using nRF Connect for Desktop on Ubuntu 24.04 LTS I am trying to use the Direct Test Mode v2.4.1 software with our own custom board.
On https://docs.nordicsemi.com/bundle...
Hi
There are some problems with nRF Connect for VS Code Command.
Most of the commands about SDK and toolchain are not available.
I have tried to reinstall vs_code...
I cannot get an ADXL345 (Adafruit breakout) to work with an NRF52840DK over SPI (Zephyr). Wiring is normal: SCK -> P1.5 MOSI -> P1.6, MISO 1.7 and CS 1.8 This is my .overlay...
NCS2.7.0
board：nrf54L15
We need a hardware to equip the nrf54l15 hardware, such as using internal or external low-speed crystal, power supply method is DCDC or LDO, etc...
Hello,
I have a thread that is reading sensor data over I2C. When I suspend it I cant access I2C from another thread that's reading another I2C device.
I tried isolating...
Hi,
I am trying implement signature keys feature in light ctrl sample . Before I do this, I have implemented FOTA over BLE feature in it successfully.
However, after I...
Hi All,
I have developed a low-power windowcovering product based on Matter 1.3, and currently, I'm conducting CSA certification testing. However, I've noticed that many...
Hello,
We created a custom board around nrf7002-DK (which includes nrf5340 and nrf7002 for wifi). We are using TF-M (including a custom secure partition), BT (child image...
Hello All, I'm new on Nordic. Could you tell me please the shortest way to flash the dongle to run as a slave for Android Blinky application?
Blinky app already installed...
Hello,
Not sure if this is the best forum, or a forum related to Zephyr would be better. I am testing with the direction_finding_connectionless_rx sample project. I have...
Hello All, I'm new on Nordic. Could you tell me please the shortest way to flash the dongle to run as a slave for Android Blinky application?
Blinky app already installed...
Hi,
I am using the NRF52840 DK. I am seeing the console logs in UART-0 and USB console (exposed as ttyACM0). However, I would like to disable the logs on UART-0, but needed...
