Hi.
I have following error:
Here is my prj.conf :
I would like to avoid using CONFIG_SHARED_INTERRUPTS.
Only GPIOTE0 is on IRQ number 11 so I couldn...
We're having an issue where our nrf52840 appears to stop advertising, and isn't able to resume advertising.
Our device is a custom PCB based on the Thingy91 (has both an...
Hi,
We are using nRF5340 DK and the nRF Connect SDK Version 2.6.1.
We are experiencing an issue with disconnections. We use bt_conn_ref() when receiving...
We have a product based on the nRF52840 which uses the GC9A01 display driven using SPI on battery power. The device also functions as a Bluetooth connectable so it is normally...
Hi,
I'm trying to implement an application that acquires data from two channels of the SAADC in "parallel". I'm currently using the nRF52 DK and nRF5 SDK v17.1.0. After...
I want to use P0.00 and P0.01 as UART pins. I have shorted the SB3 and SB4, and opened the SB1 and SB2 for using the pin as GPIO.
If I am enabling the " CONFIG_BOOTLOADER_MCUBOOT...
Hello Team,
I am using nrf52840 board which supports ZIGBEE . Setup Details: Zigbee_LIGHT_BULB (nRF52840 DK) Zigbee_LIGHT_SWITCH(nRF52840 DK)
Light Bulb Example
I am...
AWS IoT example not working with v2.6.1 SDK with nRF7002 DK but works fine with v2.5.2 SDK.
*** Booting nRF Connect SDK v3.5.99-ncs1-1 *** [00:00:00.249,725] <inf> aws_iot_sample...
Hello all,
I use nRF52840 for my custom board. I set P1.11 & P1.12 as UART_RX & UART_TX. But these two pins can not work.
Here is my nrf52840dk_nrf52840.overlay.
Here...
In the Wi-Fi throughput sample code folder the main.c file has virtually nothing in it, just a few boilerplate lines and a main() with only two lines of code that set the...
HI Nordic support team.
I have a question relate to RSSI in proprietary_rf application.
We test on esb_low_power_ptx.
Can i read RSSI of esb_low_power_ptx?
thanks...
Hi,
I have a nRF9160-DK (PCA10090, 1.0.0, 2020.50) that I am trying to flash with the Modem Shell using the Quick Start app on a M1 Max MacBook Pro, running macOS 14.5....
I am using an IMU sensor in sensor hub mode (LSM6DSV16X, LIS2MDL) with the FIFO interrupt interval set at 30 Hz. The data is sent over BLE. It works perfectly when using RTT...
Hello,
I am evaluating the nRF5340 for a potential BLE audio application. I was able to program the kit following the instructions and using the build script (or through...
Hi there,
The nRF54L15 has only 32 GPIOs, which severely limits its use in many applications. I wanted to use it instead of the nRF52840 in future products, but the lack...
I am running the nRF5340 Audio DK and trying to find a device with an app that scans BLE advertisements, but the device cannot be found.
I have confirmed that sound is being...
Is there any way in which I can use more than 200 devices in a Zigbee network?
I am trying to evaluate nRF52840 for healthcare (retirement homes, longterm living) and I...
I have my application code which builds and runs on my nrf5340DK. The project files were based on the zephyr sample for multi-advertising BLE.
Right now I'm building the...
Hey guys, I'm trying to set the max tx power for our nRF52840 project and I'm getting this error:
CONFIG_BT_CTLR_TX_PWR_MINUS_1 was assigned the value y, but got the value...
I'm presenting an issue when exporting the data collected with the Power Profiler Kit 2 in the software (nRF Connect for Desktop v5.0.0), specifically the digital outputs...
Good afternoon,
I am debugging the nRF9160 in a product, and what we are noticing is that the socket "poll" events do not appear to be generated when the system is in...
If you look at the circuit of the PCA10040, it uses a 32Mhz 12pF crystal.
C1 and C2 of the crystal are 12 pF.
However, you say to use this formula: C1 = C_L * 2 - 4pF...