Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hi Fellow NCS-ers, I understand that the configuration setting CONFIG_BT_EXT_ADV, CONFIG_BT_CTLR_SCAN_REQ_NOTIFY, and bt_le_ext_adv_create() with the appropriate callback...
I am using nrf sdk v2.4.0 and I wanted to disable TFM so I added the following definition in prj.conf.
CONFIG_NRF_SECURITY =n
CONFIG_BUILD_WITH_TFM =n
But my program...
A problem is experienced with our nRF52840 device, which occasionally stops working and cannot be reset.
Below are the issues observed:
The main software is stopped...
I am working on the broadcast_audio_source example, trying to access audio from the I2S microphone. However, I do not have much experience with Zephyr. The example is mostly...
The thread where it happens is "unknown” despite the fact I name all the threads I create. With addr2line I found that it is zephyr/kernel/timeout.c 56 but it says nothing...
Dear all,
I'm designing a circuit that should allow powering the nRF52840 board with either an USB power supply (USB2) or a (non-rechargeable) CR2032 battery (B1). According...
Hello.
I encountered the following problem. I have an nRF52840 microcontroller that is already soldered onto the PCB board. It doesn't have any bootloader. As an example...
Hi,
We have an nRF9161DK and received our own custom boards this week. When we tried to program our custom board, the development kit disconnected from the computer and...
Hi all!
I'm in the process of trying to put together an nb-iot app on Android studios that would communicate with data from the Thingy 91 board. I've been trying to go through...
Hello everyone,
I've been working on testing PPP support in SLM 2.6.1 without cmux on my Linux host machine. However, I encountered some logs during the process: Note: For...
Environment:
I can't seem to get the one button sample to do anything... I get a steady ~1sec flash from HOST led on the npm1300, but I get nothing from pushing SHPHLD...
I have an EC11 rotary encoder wired to my nRF52840 and I am trying to get readings from it using the sensor API. However, I'm having issues with (seemingly) garbage data....
Good day. We ended up getting a bootloader based on the NRF5 using the Serial Recovery method and a non-upgradable bootloader. The update is coming from a microcontroller...
I'm working on a linux driver for nRF7002 based on the experimental linux driver: https://github.com/NordicPlayground/nrf70-linux-driver . This is being done on linux 5.13...
Is it possible to somehow set a lower charge current than 32mA for the whole charge cycle or force trickle charging for the constant current charge cycle? The issue is that...
