Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hello, I am using nRF52832, nRF5 SDK, s132, and DFU-OTA with private keys and secure bootloader I am trying to enable the DFU Downgrade by disabling the define NRF_DFU_APP_DOWNGRADE_PREVENTION...
SDK:11.0 Example：ble_app_hrs\pca10040\ s132_with_dfu
Hi Does nrf52810 only support a maximum of one central connection at the same time? If I currently want to connect two...
We wanted to understand better the use of external NOR Flash for nRF9161 applications. For example, in nRF9161-DK, this would be the GD25WB256E chip.
For modem delta fw...
Hi!
I just succesfully flashed my modem firmware to version 1.3.6 using the nrf programmer and a segger external programmer. I can still connect over the serial monitor...
I used nRF52840 board with SDK 17_1_0 ,
I want to used WS2812B in my project so any one can give me reference code for this or
can suggest me how can i implement its driver...
Hi,
I am using nrf52840 and SDK-16.0. Initially I was using SPI1 and SPI2. now along with this I am using SPI3.
we have added new feature which consumes 316*9*26 bytes...
I am trying to cancel a pending connection as a workaround for .
However when I run:
```
LOG_DBG ( "Peripheral connection timeout cancelling and trying later" ) ;...
Hello . I saw this issue raised previously but with no resolution so here it is again
I built the smp-svr sample in VSCode with Zephyr SDK 2.6.1 which produced a DFU package...
Hi all,
The question is about 125kbits and 500kbits long range modulation in proprietary protocol. I'v seen a post saying that is technically possible ( ).
But is...
Hello,
I have a project in progress with an NRF52840 chip. I was able to buy an aircard with the same chip www.kickstarter.com/.../aircard-find-your-wallet-always With this...
I receive the following error message when trying to install the toolchain manager (V 1.5.0) from nrf connect for desktop (V5.0.0):
Error: Failed with exit code 1. Failed...
Hi everyone, I am trying to send data over USB port for the nrf7002 dk Could anyone have any guide, tutorial, resources, or suggestion on how I should do that project config...
We have a device that does not support bonding, however the services changed and so we want to notify devices that may have cached the previous attribute table. To do this...
Hi,
Good afternoon. I try to implement littlefs file system in my external Nor Memory. I want to store a file and then want to access the file. I am using nrf52832 board...
