Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I see many similar questions to this, but I want to double check my understanding.
We have the nRF52840 connected to D-/D+ on a USB Type-C connector. We have a standalone...
Hi all!
I'm using an nRF52833, SDK 17.0.2, s140 softdevice 7.2.0. My design uses a Skyworks SKY66112 amplifier.
I have the pa_lna_assist function that I found here on...
I am running the example:
C:\Nordic\nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10040_uart_debug\arm5_no_packs
Everything seems to be working well except...
Can you please provide security manager keypress notification sample program for bot peripheral and central program. I want to know why it is used and what is the main purpose...
Hello Nordic team
I am developing a BT mesh network project, which be implemented by nrf52840. Right now I am designing the node PCB. I want use the No.4 reference circuit...
Hi,
I tried to implement my custom service.
I followed the tutorial from this site: https://github.com/bjornspockeli/custom_ble_service_example
For SDK 15.0 it works...
I'm attempting to connect an SDcard (micro SD) to an nRF52840-DK via a breadboard setup. I'm running Zephyr and it appears that configuration is to be performed via device...
I'm trying to investigate whether I should ditch BLE in favour of Gazell and ShockBurst (to avoid the $8000 Bluetooth.com fee)
I've noticed that Gazell has no entry in the...
Hello,
I've got this Thiny:91 demo working nicely, but what I'd like to do now is only measure RSSI.
Is there firmware to only do this?
Like send AT commands only to...
Hello,
I've been trying to perform a dfu to a target Nordic device over Bluetooth using an nrf52840 dongle distributed by Laird, however whenever I attempt to run the command...
Hi guys,
I am trying to create a zigbee mesh with 10 devices with 1 coordinator and 9 routers (all are nrf52833 based custom board). I can create a mesh network easily with...
Hi,
I understand that white list can be enabled at the peripheral side. I also know that if white listing is enable on the peripheral side then it wont respond to centrals...
Hi All !
Hope you are doing well !
I have tested some examples using SDK 17.2.0 and it worked fine ! .IDE i used is SEGGER IDE . Now i have a question that my next HW...
Hi,
I'm testing the USBD BLE UART Example with nRF52833 DK, after programming the app, the LED3 keep it off all the time as followed.
In the device manager, I can see...
I'm porting from 1.2.0 to 1.4.2. I'm using mqtt_simple as a baseline but I'm connected to Google Cloud. I successfully create a socket;
net_mqtt_sock_tls.mqtt_client_tls_connect...
