The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hello, I want to make periodically wake up nRF52840, performing some work (connecting to MQTT broker, sending some data) and after that going to low power mode. Then the nRF52840...
Hello,
We want to use a nrf52840 as a logic controller which reads data from Modbus RTU Sensors (as Modbus RTU Master) and simultaneously is the Modbus RTU Server for an...
Hello Team,
We are trying to make Release and Debug mode for our software.When I compile a sample program I see lot of Debug information in the Mapfile. Will this influnce...
Hi Support team:
I'm using Zephyr cellular modem driver on the nRF5340 and set APN in prj.conf with 'CONFIG_MODEM_CELLULAR_APN="telenor.iot"' now. I need to set APN value...
Hello,
When building my project although the terminal doesn't show me using all the RAM, I get the following error message which fails the build.
I am using a...
Hello,
I was working on a ble communication using two nrf52dk boards while one of the two stop responding. The board is correctly recognised by the computer and segger asks...
When I am on to collect the accelerometer data from Thingy-53, only 3 sampling frequency options are provided which are 20 Hz, 62.5 Hz and 100 Hz as shown in figure. Please...
I am new to nRF chips and currently working with the nRF52810. I am developing with nRF Connect SDK and VSCode.
I have encountered an issue with the Blinky example (ncs...
Hello,
when creating a multi-image build is it possible to select the optimization level for each image individually?
Below is an example of the issue I am facing currently...
Running the Ciphersuites sample code on the nRF9161 I get Connection Refused on all attempted ciphersuites. Including after adding the CONFIG_EXTENDED_CIPHERSUITE_LIST=y to...
Hello,
Dev board: nRF52840 development board.
OS: Zephyr (NCS v2.6.0).
My requirement and What I am using...
- I want to perform DFU for application core & bootloader...
Hello Nordic Team, I am using nRF5340-DK and I have a PPK-2 for current measurements. My development environment is NRF Connect SDK v2.5.2. I used https://infocenter.nordicsemi...
Hello,
I am using the "direction finding connectionless beacon sample" to test various settings of the beacon. About setting parameters, I have the following two questions...
