Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello,
With the CMakeLists file, is it possible to make an error during compilation if the SDK version is not the correct one?
Example: I am developing an application...
I'm trying to modify this bit-banging ws2812 gpio Zephy driver to run on an nrf9160 board. The problem is I can't mange to get consistent pulse timing using assembly instructions...
Hello
I have a problem setting up communication between a nRF9161 and a nRF52840.
I have a custom board with a nRf9161 and a nRF52840. These two are connected with 5 lines...
Hello, I'm using the nrf5340 and nrf Connect SDK 2.6.1. Currently the MCUBoot is immutable and the cpuapp image is encrypted (it contains IP and secrets). The MCUBoot is kept...
Hello,
I 'm updating from Zephyr 3 .2.99 to Zephyr 3 . 4.99 .
I attempted to add a main() function to my application . (Heretofore I have not been using a main() function...
hello I am designing a custom PCB using an nRF5340 and i have one nRF5340 audio dk with me and both are configured as a gateway and headset . i am facing an issue in pairing...
To do this by reusing the sample of nRF5340 Audio I am thinking of using it by editing the overlay file.
nRF5340 Audio has A/D linked to P0.24, Use P0.24 separately from...
When I tried to use the sd_ble_gatts_value_get() function and found no error but no corresponding value returned, I was sure I had the right value in my feature because it...
Hi,
I try to create a one-button minimal "smart watch" based on a small nRF52840 module (register button press) and a second nRF52840 'central station' (receiving and converting...
hi there i hope you are doing fine and best of your health. actually i am developing the custom app to communicate with nrf 52840 soc device through bluetooth, which is working...
I am using PCA10056 3.0.2 dk for my application
when search for schematics of this version board I am getting 1.0.x https://docs.nordicsemi.com/bundle/ug_nrf52840_dk/page...
Hello everyone,
I'm looking for some advice on a slightly offbeat topic related to the Nordic SDK.
I'd like to modify the Makefile of one of the SDK examples so that it...
Hi there!
I am trying to make an application that plays an audio sample to a BLE speaker (another nRF5340 running as headset) where the audio sample is in memory. I have...
Hello,
I am writing to inquire about an issue occurring on our custom board.
Ideally, we should print the logs from the device to identify the exact cause, but since that...
Hi everyone!
I have been developing an application for some time and everything has been running smoothly, until recently testing it and finding out some inaccuracies. ...
