The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I was testing out the custom application from android studio, and have discovered that, for example, when using the rscs example my application does not see the device and...
Hi Nordic. This is a general question and could as easily have been posted to stack overflow but I have found the members and staff of this community so helpful and adept...
HI,
I am working on a application which has an requirement, that I need to read the current value if it is above threshold value then I need to turnoff the control. Here...
The executed command at connectedhomeip/examples/lighting-app/nrfconnect: west build -p -b nrf52840dongle_nrf52840
The messages i encountered:
...
/ncs/zephyr/include...
good day,
is there a way to set a gpio when in dfu mode? wanted to make GPIO 19 of nRF52832 HIGH during DFU mode because we assigned it as an enable pin.
in DFU mode,...
Hello,
I have my own custom board with nRF52832 and a NB-iot module SIM7080G that interfaces via UART.
I can easily program the device through SWD using J-Link. I am even...
Hello,
I am using flash_write_protection_set function with few low level function call for accessing extremal flash with nRF9160. And because of that I am facing one warning...
Hi,
I am programming the nRF52833 and using NCS v2.00. I have recently programmed the Peripheral Coded PHY to the board. I am using a Google Pixel 3 with nRF Connect as...
Hi,
Can we use the PPK2 kit for measuring current consumption in any other reference design board from a different
vendor which is not same as DA. The other vendor does...
Dear person in charge.
Before using PPK2 for a evaluation of current consumption, I checkd power supply vs corrent measurement by using PPK2 and 5kΩ chip resistor.
I...
Dear All,
I am building an application that needs to use NB-IOT and if that is not available then use LTE-M. I tried sending this AT Command:
AT%XSYSTEMMODE=1,1,0,2
...
When building the Matter Light Bulb sample application for the nRF52840 fails with:
/opt/nordic/ncs/toolchains/v2.1.0/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm...
What is meaning of error code 0x3004?
The following is source code of calling sd_ble_gap_tx_power_set().
int _gapTxPowerSet(const int8_t txPwr) { ret_code_t errCode;...
How do we read/write the preferred carrier lists on the SIM card with the nRF9160? Most modems provide the at+cpol command but this doesn't seem to be implemented on the ...
Hi,
We have an application where I'm trying to maximise BLE data throughput to it's absolute highest I can get. Through reading docs/researching and doing some experiments...
