Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
My query is:
1. Is it possible to access the azure using WIFI network in above application?
2. After knowing the IMEI using AT Command, in response to which event should...
I am getting more current consumption when internal pull up resistors of nRF52832 are disabled and external pull up resistors of the slave sensor are enabled as compared with...
Hi,
Currently, I am building an application with Bluetooth mesh and I tried to use Zephyr's logging v2 modules. However, when I build it I get MPU-fault errors at boot....
Hi,
I saw in ozone that SW crashed with hard fault explained as escalation of exception that was not enabled.
How can I enable all exceptions to see the exact reason of...
Hello, I'm using nrf52833, pca10100.
My project is based on 'ble_app_uart', and I added buttonless DFU project.
this is ble_dfu_buttonless_async_svci_init() function...
I have succeeded in running the Multi-NUS package on the nRF52840DK. My client's client learned of the nRF21540EK and wants to try using it to extend the range in the present...
i cannot seem to select nRF Connect SDK when creating application in vs code. i already install the nRF Connect SDK v2.0.0 from the toolchain and the nRF Connect Toolchain...
I am trying to build a example program in KEIL for the nRF52832 QFAA device. When I sart KEIL the program shows a massage that says the nRF_DeviceFamilyPack.8.3.1 is required...
Good day to all I am trying to change the Application on a device with an nRF52832 chip with an existing firmware. To do this, I use nRF Connect for Mobile 4.25.3. From the...
I am developing GATT Server Reader Firmware usng nRF SDK COnnect using NRF52840
I have implemented two services in reader FW in two files say: service_a.c and service_b...
I have tried installing the nrf connect 3.11.1 on 2 different windows 10 machines. Both are clean windows 10 installs. The hard drives were wiped and windows reinstalled....
Hi,
the following event is generated when I connect two or more nRF9160DKs to a Windows machine: "Disk 2 has the same disk identifiers as one or more disks connected to...
1. 2. 3.
I am using the ble_app_beacon example as the starting point for my project. I am working on a project where a number of beacons will advertise its identity and...
How do you enable any of the i2c peripherals on the nRF9160 dk boards?
I tried changing the device overlay to the code below:
& i2c0 {
status = "okay" ;
compatible...
Hello,
I have a project that uses JWT.
When migrating from nRFConnect SDK 1.6.1 to 1.9.1, build failed with message: multiple definition of `default_CSPRNG'
The error...
