Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello Support,
For my Zigbee Coordinator development I use nrf Connect SDK 1.9.1 (for now), and VS, I like using Kconfig GUI as much as possible.
I'm trying to find some...
Hi, we have the requirement for our peripheral to be able to disable Bluetooth functionality, i.e. disconnect any connected central device and not accept any new connections...
Everything is goes well with nRF5340 but when I connect and try to debug some examples it just gives some errors.
Like " Failed to download application
Generic error ...
When connecting to AWS IOT the Asset Tracker V2 uses MQTT to AWS-IOT. This is TLS 1.2 from what I understand. We are using the 1.8 skd / 1.3.1 modem firmware.
We have...
I have ran a test with the nrf9160-dk board.
Setup:
PCA100900 0.9.0 pcb
NCS 2.0
Modem 1.3.2
App: ncs_v2.0.0/nrf/applications/serial_lte_modem
modification: change...
Hey ,
I am using a thingy 91.
I want to use this GNSS sample to get the location, but I do not get any fix. I have tried outdoors too, but nothing happens. I have the...
Hi,
I am working with NRF DK board, I need to connect nrf dk with remote control for data transmission and also the remote connection should be stable for long time. Is...
Hi All,
We are in the almost finishing phase of our application development, and running out of flash memory space, all details are listed below.
MCU : nRF52805 (192 ...
If I am not currently connected to a network and use AT%NCELLMEAS=0, how is the RPLMN determined? Are previous connected PLMNs stored in RAM in the device for comparison or...
Hi,
I'm using SDK v14.2.0.
For the workaround of [107] RADIO: Immediate address match for access addresses containing MSBs 0x00
I'm trying to avoid the addresses...
This is with the nRF 5 SDK (17.0.2) and the S113 softdevice.
We have another microcontroller connected to the nRF52833 over UART and external flash. We modified the bootloader...
Hi,
I'm currenty try to code GPIO wakeup from System ON sleep with system_on_wakeup_on_gpio as a reference.
My circuit is powerd by solar panel via control board. In this...
Hi,
I would like to know what is the default state of GPIO pins when nRF9160 is power ON for the first time, and it has the pre-programmed FW from Nordic
Hi,
What is the expected format to pass to nrf_cloud_agps_process()? I am working on an LwM2M server and want to be able to respond to /50001/0/{0,1} request coming from...
Hallo,
I installed the ncs and Zephyr environment following mainly the guidelines from nordicsemi, a few changes were necessary to use Eclipse. The installation process...
