The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
Sir,
Writing Android Software to receive bytes from one of your ble chips for the UART design. Editting nrF ToolBox app.
UARTService.java
onDeviceConnected(BlueTooth...
Development Software: SDK v15.3, IDE IAR v7.8, SoftDevice 6.1.1
Computer Platform: Windows
HW revisions: EYSHJNZWZ (nRF52832)
Hi,
My application requires SPI and...
Hello Team,
i am evaluating Custom software Codec inside nrf52840. need development help whether it supports custom codec or not? which bluetooth stack used for development...
I'm working on a NRF52832 project with SDK V15.2, using S132 Softdevice. before connecting, nrf_fstorage_write/nrf_fstorage_erase/sd_flash_write/sd_flash_page_erase all are...
Hi.
I am using SDK15.0.0.
I tested the RF communication through the ESB example.
And I have tested the BLE communication using the ble_app_hids_keyboard example. ...
Hello all
currently I am flashing the device using command line:
#erase chip nrfjprog --family NRF52 --recover #program softdevice nrfjprog --family NRF52 --program...
Hello,
I'm trying to read an ADC value from a sensor(for POC I'll be using a pot wired to 3.3V VDD and GND) but all the examples I found only demonstrated reading the internal...
Hi,
What is your recommended stand-off for your aQFN package to PCB?
Below image is from x-section after mounting nRF52840 to PCB, these are aQFN pads, could you advise...
Working with NRF5 SDK 15.0.x, if I configure an GPIO as output, its initial state is low. I can set it high after configuration, but it is briefly low. Is there anyway to...
Hello to everyonel.
I am working with the Light_switch example of Mesh 3.1 on nRF52832 (PCA10040). At this moment, I am trying to understand how I can send a message from...
Hello!
I want meashure pulse time via input capture.
I configured NRF_P0, NRF_GPIOTE, NRF_PPI and NRF_TIMER1.
It work fine, but in datasheet I found next text: ...
Working with NRF5 SDK 15.0.x, if I configure an GPIO as output, its initial state is low. I can set it high after configuration, but it is briefly low. Is there anyway to...
Hello,
I've got an nRF52832 embedded in a module (Telit RE866). As such, I can't see the markings on the chip and have to resort to reading the FICR registers to identify...
