Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
when I tried to add a device to nrf cloud, I am getting an error message 40101
My device is nrf9151dk with IMEI 359404230049133 and HWID 374155 I believe I might have registered...
I am exploring the possibility of using ncs v2.8.0 for Mesh with Coded PHY on the nRF52840dk/ nRF52840 board . I know this is not officially supported.
I started with the...
Dear,
I’m using nRF Connect SDK 2.7.0 with BLE Mesh and wondering how to adjust the TX power dynamically. When setting the TX power using a predefined option like CONFIG_BT_CTLR_TX_PWR_PLUS_8...
I've tried to follow the exercises from the Bluetooth Low Energy Fundamentals course. When I try to run the solution for lesson 3 exercise 2 I get the following error messagen...
Hello,
I have some previous code that ran using BT mesh. I then updated SDK's to 2.9.0 and I am now having issues provisioning devices. I am using the BT Mesh Provisioning...
Hi,
We are currently developing an application where we use a nrf52811. Currently i am working on integrating the BLE-Stack as this is the last part missing.
I am constantly...
Hello -
I am working through the DevAcademy - nRF Connect SDK Intermediate lessons. I have reached Lesson 7 Exercise 1, found here - https://academy.nordicsemi.com/courses...
Hi Team,
For my project, I am using nRF 5340 board and using the Zephyr SDK for development. I need to read and write data from/to an external QSPI EEPROM used ( MP95P08...
Smartbadge epaper custom board using nrf5340/nrf7002, with an NFC loop to allow NFC card emulation/communication. Building using NCS2.9 with sysbuild.
I want to be able...
Hi,
I just have a simple question => could you please tell me what are the ECCN numbers associated to this software:
www.nordicsemi.com/.../nRF-Connect-SDK
Thanks in...
-- west flash: rebuilding [0/16] Performing build step for 'tfm' ninja: no work to do. -- west flash: using runner nrfjprog -- runners.nrfjprog: reset after flashing requested...
Hi,
We are currently developing a solution where a Thingy91 acts as a BLE central. We have had a lot of issues with BLE when using the nRF52 as a HCI device being controlled...
Hi guys,
Maybe someone already did this work but if no:
I would like to take only the relevant parts to my project.
I am not sure what can be given up.
I need cellular...
Hello!
I would like to know what are the minimum, maximum and recommended current values for the VDD, VDDH, VSS and VBUS supplies. The voltage values are listed here...
