I thought this should be very simple but it has not turned out that way. I have started with the pc-ble-driver heart rate monitor (peripheral) example. I was able to take...
Hi,
I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central.
The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
Hi Community,
I made a custom board based on thingy53.
the custom board can be flashed with nRF5340-DK, I see the " merged_domains.hex " is flashed.
Also tried with...
Hi
Default value of NRF_SPIM0->IFTIMING.RXDELAY = 02 based on the datasheet, but it always shows 0x00 on debugger and I can not rewrite it.
Has anyone entered the same...
I want to use the example of "Wi Fi: Shell" to set TWT parameters by referring to the official documentation：
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols...
I see that the NRF24L01P is not recommended for new designs.
Since this product is in our production currently, we want to now the following things
When will the NRF24L01P...
Hi,
I'm trying to build the ZigBee light bulb sample on nRF52840 dongle.
It compiles. 1 LED blinks, and the other 2 are steady, which supposedly indicates that the dongle...
We are using an nrf52833 with the nrf21540 FEM and are getting a fault. Even with a basic BLE example, we are getting this fault. When we use a board that does not utiliize...
I need to detect the VCC voltage on the nrf52833 on power-up and wait till it slowly ramps up to 3V. Is there a way to do this using the Power-Fail Comparator. I found another...
I am using an nrf52833 with both 32.768 kHz and 32MHz external crystals (identical to the DK). When I go down to -30 deg C, the uart stops working. I believe that this is...
Hi
I'm trying to use the nRF Cloud Provisioning Service with the nRF Cloud multi-service sample in SDK 2.6 on a nRF9151DK.
I have got the token from the device using AT...
Hi,
Do you have sample ios reference code for app that I can start developing?.
I have been searching the web and couldnt find a good example. basically for updating firmware...
I use ncs v2.7.0.
I am evaluating to connect 250 nodes in BLE network . Each node sends BLE packet periodically for every 100ms.
In project sample, periodic_adv_rsp.c...
Hello,
I am running the SDK on Fedora 41 Workstation using VSCode (Codium) with NRF Connect SDK Extensions. Everything was working fine with v2.7.0 SDK installed using the...
I am having nrf52840 dongle,my purpose is to make it a peripheral device,enable gatt,change tx power through gatt.i uploaded blinky hex code(compiled in vs code ) to the controller...
I am using nRF52833DK, zephyr v2.7.0.
I want to disable hardware nRST to use P0.18 as GPIO.
What I did
Added to Kconfig : CONFIG_GPIO_AS_PINRESET=n
Removed : gpio...
I previously tested the peripheral_ams_client with iOS 17, and I could select the device in iOS Bluetooth settings to connect to it, however it appears in iOS 18 iOS is not...
