Hi,
I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central.
The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Hi, in our project with the nRF5340 we desire use the nRF21540 to have a long conection for BLE, the problem is we don't have any pin free in the nRF5340 to manage the nRF21540...
I have configured new UART in zephyr.dts device tree like this" "/ { chosen { zephyr,console = &uart1; zephyr,shell-uart = &uart1; zephyr,uart-mcumgr = &uart1; zephyr,bt-mon...
my device acts as ble periph ,case BLE_GAP_EVT_DISCONNECTED in ble_evt_handler , if do m_conn_handle = BLE_CONN_HANDLE_INVALID,current changed to 2.5mA, if dont, current is...
Hi,How can I force mcuboot to use a specific serial port for logging?
chosen {
zephyr,uart-mcumgr = & uart0 ;
zephyr,console = & uart1 ;
zephyr,shell-uart = & uart1...
Hi,
we have created a new product prototype where audio streaming is the functionality. 2 different HW revisions were so far built, the software originally is built to use...
I am trying to make the broadcast _audio _sink work . It is always stuck with the following logs :
Broadcast Sink created, waiting for BASE
which then times out with ...
We built a custom version of the Direct Test Mode sample in our firmware, using the USB shell to interface with the test operations and removing the UART or HCI interface...
I have a IMU whose interrupt is connected to GPIO0.11 which is also nrf-gpio-forwarder GPIO (which I dont use)
I managed to get it to work but lost that progress and cant...
Dear Nordic
Question 1: How many bytes can the Rf Tx of the current Nrf52810-QFAA transmit at a time? Now I can only send 256 bytes at a time. Can I send 512 bytes at a...
Hi there,
I always have to start up nrfconnect-5.0.2-x86_64.appimage and then select the power profiler. How can I directly start up the power profiler?
I can see that...
Hi there
I wrote a program (include of advertising, pairing and connecting over service, characteristics) for nrf51822QFAA and work well for C0 build code (nrf51822QFAAC0...
I want to know the power saving mode of nRF5340. Dose this chip set have the following mode ? 1. each BT products connencts, however, the data were not send. above condition...
Today I tried to use the bt_conn_le_param_update() method to update the connection parameters, using the following values.
interval_min = 3000
interval_max = 3000
latency...
Hello,
We can successfully build and flash the ncs/application/asset_tracker_v2 example code in nrf9160. But when trying to boot up, it throws the following error:
**...
Hi there,
I'm using a nRF5340 to generate an 8MHz signal and would like to force the HFXO to always be used as the HFINT is not accurate enough. I have verified this with...
