Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Hi,
I am using nRf SDK5 and have a sensor that I am trying to extract the Eddystone UID data from the advertising packet. It shows up in nRfconnect as:
Eddystone UID...
I installed the nrf connect 3.91 with programmer v2.0.1 and J-Link driver v6.88a. However, when I cant seem to see the dev kit on my windows 10. I tried holding the reset...
Hi everyone,
I want to use the RTC module in my code, and I have some questions.
1. What I have understood so far is that the nRF52840 has three RTCs (RTC0, RTC1, RTC2...
Hello,
When using eDRX alone and without DATA (eDRX=81,92 sec, no PSM, no data transmittion,iDRX PDCCH = 1), it's showing an average current of 17,84 uA. This value is similar...
Hi Support team,
I have downloaded nRF5 SDK and found that there is a sample for serial via UART but however the samples ( <SDK Folder>\examples\peripheral\uart) is available...
Hi,
I've designed a product based on nrf52840 soc as a central Bluetooth device. I want to pair and connect to a Bluetooth device (as a slave) that implements a whitelist...
Hello,
When AGPS is activated and trying to fix location, the user see only the final respond once fix is done, but we need to know where the satellites table is stored...
nRF21540
We want to use the nRF21540 FEM to improve BLE range and performance within a building. How does the Tx and Rx amplifier operation coordinate with the BLE SoftDevice...
Hi,
Related to this topic BLE DFU, MCU to MCU (Zephyr), GATT DFU SMP Service Clinet
I would like to know if anyone has any luck in making a SMP client for DFU updates...
I moved to a new computer and reinstalled all the tools and moved my code over. Now, when I compile, I get the following error:
Here is the code from the board definition...
I have an nRF9160DK that I'm trying to get a demo running per this video: https://www.youtube.com/watch?v=rMvW3HXLErk&t=832s
The board label says PCA10090, 0.8.5, 2019...
I had used ble_advertising_advdata_update function to update my scan response data in ibeacon by getting error as mentioned below:
.\_build\nrf52832_xxaa.axf: Error: L6218E...
I'm trying to get basic i2c code working on my Nordic nFR9160DK board. I'm new to the platform and have been doing a lot of reading and searching through examples. Through...
Hi
In order to work on never zephyr version I have tried updating my ncs v1.7.1 folder to origin/main with:
git fetch origin git checkout origin/main west update
After...
Hi,
Does the ratio of gain error and offset error change when the ADC gain is changed?
For example, if the gain is 1 and the gain error is 4% and the offset error is...
