hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
I have a SPI Master and a SPI Slave. The Master will randomly pull data over SPI from the Slave. The slave will randomly generate events that result in data to be sent to...
I am using SDK version 17.0.2. The example code uses SPI.
The following changes have been made to the pin settings.
Questions
1. Pin behavior is strange.
...
Hello, Support team.
Our boards do SPI communication to read sensor data.
Basically It works well. I checked that It operates more than 5 hours.
But only one board...
Hi,
I have the following initialization for advertising:
The name consists of an acronym od three letters and a underscore e,g, XXX_ and a six digit ID. Like XXX_12E124...
Hi,
Is it possible to add four pairs of resistors between the debug signal lines and the connector as shown in the figure below.
Would such a connection not impair the...
The Google Fast Pair Service has recently been included in a number of Bluetooth peripherals (Headphones, fitness trackers, etc.) and has been getting rave reviews.
Has...
I am able to download simple blinky program on my custom board. It is working fine. Custom board is interfaced with nRF52-DK through P19. I am using embedded studio as IDE...
Hi, on nRF5340 I want to capture accurate timing of external events. I need a kind of real-time capture module to read the time period of a pulse train generated by a rotating...
Have a few questions about ble_app_uart example.
From the way I see it, it sets uart_event_handle as the callback, and every time there's an "event" that takes place...
Hello All,
Method 1: I am writing a test application to read the ADC data at a specific intervals(10 samples for every 5ms interval for every 50sec). I am using blocking...
Hi,
We are implementing a synchronous light flashing of multiple devices, so:
1) Can we get a millisecond level (< 10ms) time synchronization by parsing the Link Layer...
Hi, all
I added a scanning module to the example 'ble_app_uart.c', so each one works well.
What I want to do is advertising and connect at the same time while connected...
What is the best practise for multichannel SAADC conversion in ultra low power devices? For example I have to measured 4 channel in interval 250ms. Below what I try:
...
Hi, Dear Nordic & all:
when I run the ble_app_hids_keyboard example in nrf52820(SDK17.0.2), I meet a question:
1、Frist I use my iphone connect ble device and pair success...
Dear Nordic:
so I want to know In nRF52 serials chips, How much HFCLK CONTROLLER ppm is the frequency offset distribution and production FT control range? Do you have any...
