I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hi All,
I am using the light switch example and have modified it a bit to send packets of data. I am able to send data from the client to group address, by setting the...
I have two beacons which are UUID filtered successfully.
I am trying to fetch major but this cannot be done just by putting an offset to p_adv_report->data.p_data. I noticed...
Hi,
nrf52 using from ble-peripheral-> ble_app_uart examle
In that ble_app_uart example receive the data from the android is ok.
But,i want transmit array type of data...
Hi.
setup is 52832, S332, SDK 15.3.0.
issue is about reset voltage.
I use CR2032 for power supply.
repeat fast put on and put off CR2032 on custom board, sometimes...
Hi All,
I am using nRF52382 and sdk 15.0. I have two SPI devices using separate pins. They work just fine separately, when I try to enable two instances I get compilation...
Hi,
As mentioned in "nRF52840 Product Specification v1.0", I have setup the high voltage mode, and use VDD as an external power of 3.3V by setting NRF_UICR -> REGOUT0 to...
I want to use 52811 as central deice, which SDK and SoftDevice should I use?
https://www.nordicsemi.com/Software-and-tools/Software/S140
It says: SoftDevice S140 is a...
Hi,
I’m looking to build the Bluetooth HCI-RPMsg sample for nRF52811.
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/samples/bluetooth/hci_rpmsg/README...
Hi,
If the app keeps sending data at a certain rate, the numbers will skip and the software will stop.
I tried to see how much data I could communicate and at what speed...
Hello,
Development to blink LED only on Nordic Thingy 52 has been started after referring the following one of the post from Nordic Devzone. https://devzone.nordicsemi.com...
Hi,
I am using nRF52840 DK with ble_app_ots sdk example. When flash the ble_app_ots to my nordic board and I am trying to connect the board with my mobille. Unfortunately...
nRF9160 GPS IGPS_CONTINUOUS_PSM - can you please explain the basic functionality when the GPS runs in power save mode (to reach 9,8 mA). I cannot find information in the data...
DK: v0.9.0 nrf: v1.2.0 supl fw: v0.5.2 modem fw: v1.2.0 OS: Windows10
I'm trying to use assited GPS in "gps" sample program, but it doesn't work. This is log. There is no...
