Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
hello,
Now i remove pwm_library programming in ble_app_uart_c(central) of SDK15.0 to produce a 125KHz PWM waveform.
But i found the program cann't run in NRF52 DK.
pwm_library...
Environment: nrf52832 , nrf5SDKforMeshv310src , nRF5_SDK_15.2.0_9412b96
0.did the switch_light sample use FressRTOS ?
1.if not use , can i use FressRTOS directly ? does...
Hi,
I have a device with two models, the Generic OnOff Server is located on the second element. When using the "Node Control" to change the "GenericOnOff state" the app...
Hi,
I'm using SDK 13.1, SoftDevice 4.0.5 on nRF52832. I have an app which runs for a long time but will occasionally enter the hardfault handler from an address within the...
Hello,
I try to send multi notification in one connection interval, but I can only send one notification.
Hardware
Peripheral: nrf52832 costumed board (with BMD-300...
Hi,
I'm using nrf52 custom board designed for our project,For this we have P0.09 and P0.10 as rx and tx used for uart, when i configured this two pins as rx and tx it is...
Hi
I am running on a nRF52832 chip with following software stacks
Mesh SDK v3.1.0
nRF SDK v15.2.0
Softdevice v6.1.0
I am working on a use-case where I am processing...
Hi
I want to get a certification. I need your help because I am not currently in DTM mode.
The procedure I checked is as follows.
1. J-LINK , USB to Serial Converter...
Hello to all,
I am using nRF52840 with SES SDK15.0 version. My device is goes into sleep mode after sending data to server. But when woke up device for first reading data...
Hi,
Can someone please tell me in what scenario would a device advertise with two different addresses at the same time?
My device is an nrf52382 based custom PCB...
I am try to register nrf9160 DK sim card, but keep getting fail to fetch error. I had made sure that I am entering correct sim Id and the puk but so far no luck to getting...
Hi,
I am using NRF 52832 S132 sdk 15.2.0.
I am working with example project <install folder>\examples\ble-peripheral\experimental\ble-app_multiperipheral.
I added NUS...
Hi,
I am testing the at_client sample code in the nRF Connect SDK.
I want to change the default AT host com port to uart1 or uart2.
I tried to modify prj.conf but it...
