In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Related to SDK 12.3.
Quoting this question :
GPIOTE PORT event generated on the
rising edge of DETECT signal. Please
have a look at section 15.1.2
2)DETECT...
Hello,
I am experimenting with sending large notifications from an nRF52 configured as BLE peripheral with SoftDevice S132 v5.0.0. I having some trouble receiving the notifications...
Hello guys,
I would like to execute code once a scan request from any other BLE device is received by the NRF52 using Zephyr.
Unfortunately, I am not able to receive...
Hi everybody,
I have an issue with my application, I want to use the ble with the same antenna that it use in the development board PCA10036,
Could you please tell me...
When I send 512 Byte from my Android phone I received only 20 Byte. How I can received more than 20 Byte? I used example project "ble_app_uart", SDK 14, SoftDdevice s132,...
I am working with SDK 14.0 . I see two "type" of advertising_init() function :
1-
static void advertising_init(void)
{
uint32_t err_code;
ble_advertising_init_t...
Hi
I have successfully run the light control example for BLE mesh. Now if I want to add another server to the network, how do I do it without bringing the server in the...
I am using the ble_app_uart example from SDK13 and something strange is happening. The code without UART part works nice and I can see in RTT that it can discover every beacon...
Hi everybody,
I have an issue with my application, I use the nRF52832-QFAA with the following circuit, when I open the application Nordic 'nRF Connect', I detect the ble...
We have a software application for the NRF52 with BLE communication. The communication part is based on nordic example “ble_app_hids_keyboard”.
We are using Softdevice...
Hi there,
I am using the uart example with SD130 and added neopixel code from GIT to drive the WS2812B LEDs using bit banging.
I want to update the LED every ms. The bitbanging...
I am getting random data while using saadc example to reading analog voltage applied to pin on nrf52840. i want to read analog output from MQ135 gas sensor, I have applied...
Dear all,
by looking at the sdk code, specifically that of s132 component, I understand that the length of the PIN code is statically set to 6 and cannot be changed.
...
We have been using nrf24l01+ for sending few bytes between one Master(Master MCU board) device and many slaves(slave MCU boards). Each time Master Device queries data from...
I installed nRFprobe driver to program and debug my nRF24LE1 chip from Keil. I am using a nRFgo 6700 starter kit for flashing and debugging purpose. I connect ISP connection...
