I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hi,
We're planning to integrate ble_app_uart and ble_app_uart_c into our project. Before integration, we tested the ble_app_uart example code on one development board. After...
Hi all,
I'm trying to get a UART connection running at 460800 bps, and it fails about 1-5% of the time, meaning that I receive less bytes than I expect. This happens a lot...
Hi,
I want to debug [i.e. attach to and single step] mcuboot [running as second stage bootloader] using Ozone and JLink.
I can connect to the board via the debugger...
Hi! I am trying to sync the time on my nrf9160dk with date_time_now() or date_time_uptime_to_unix_time_ms() but it seems that they return a very low unix_time_ms (only 1089262423ms...
The nRF7002DK board has a Vdd of 1.8 V, unlike every other Nordic board I've seen which use 3.3V. I assume this is due to the nRF5340 errata that state that the QSPI bus ...
Hi,
We are Designing the Long range module using nRF54L15 with nRF21540 FEM.
Now want to use Dual Antenna simultaneously. we have Couple of questions
Please guide us...
Hi all,
I am currently working on a personal project with hundreds of nodes. I have created a device with remote provisioning models (server and client). In my network...
I'm encountering an issue while trying to use the CAF LED module with the nPM1300 PMIC. Despite configuring the Device Tree, prj.conf, and led_state_def.h, I'm still getting...
I would like to confirm if my understanding is correct regarding calculating the average current consumption using the PPK2.
As shown in the image, the Selection Average...
I can't find any mention about MU-MIMO in the datasheet. Does the nRF7002 support MU-MIMO TX and RX?
I cannot find any details of if support is mandatory for a 802.11ax...
Hello,
I need to implement Find My Device for nRF52833.
From Sample I could find "samples/bluetooth/fast_pair/Locator Tag" example. I tried to go through it. but I could...
Hi,
We are using the nrf52833 for development.
The first version of the program can connect to the discovery service normally. But we need to add some new features. And...
Lesson 8 of "nRF Connect SDK Intermediate" DevAcademy course deals with Bootloaders. I've successfully done the exercise of updating firmware using the off-the-shelf mcuboot...
hi,i wanna read the imu sensor lsm6ds3 on board of nrf52840 based Xiao BLE Sense
so i used the code in samples /sensor/lsm6dsl
first i didn't know if i do have to create...
I'm trying to use the nrf_desktop application 100% standard, with NO changes to the codebase at all.
My initial assumption is, that once I flash the nrf52840dongle, it should...
