Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
SDK version : NCS 2.1.0
Hardware : nRF52840 DK (External supply)
I am trying to put the nrf52840 to idle mode based on the system_off example.
D:\NCS_2.1.0\v2...
If I send 0x33 through the project example in the directory “nRF5_SDK_17.1.0_ddde560\examples\802_15_4\wireless_uart”.I can see the data 0b 61 88 01 34 12 0b 00 0a 00 00 33...
Hey
For nNR2805, using SDK nRF5_SDK_17.1.0, when we include the LESEC Pairing, we got the binary file with a size bigger than the flash size
Should nNR2805 work with the...
What is the behavior if back-feeding the nPM1100's VCC output, such as if VCC is supplied from a external supply and no battery or USB power is present.
I have been bringing...
Hello!
Tyring to configure the uart rx/tx pins pull-up, pull-down or open-drain using the ncs 2.0.2 . So far I couldn't do it. For example "bias-pull-down" seems to have...
Hi there, I'm having trouble programming the Nordic Thingy:53. I've got a nRF53 dev kit connected to it via the 10 pin connector (as per the instructions) and of course I...
hi，
I`m project NRF52840-SDK_17.1.0。 How do DFU use the uart?What applications do I use for Win7?I read a lot of other`s qusedions-answers,but I still don`t know how to...
I have a working project on a custom board based on nRF52832 ( PCA10040, S132). This board is a BLE Peripheral.
My task is to migrate this to a custom board based on nRF52833...
Hello, I've been using the modem library from NCS1.7.0 specifically 'at_cmd.h' and at_notif.h'. Now I'm trying to port to NCS2.0.0 and I believe that the AT CMD interface...
Hi,
I've got a display driven over SPI at 8MHz by the lib LVGL in a dedicated Zephyr thread and an ISR configured on one gpio pin that triggers a short routine registering...
Hi,
I'm testing the matter commissioning from your sample "light_bulb" on the nRF Connect SDK v2.1.0
I have this setup:
- One nrf52840dk flashed with the light_bulb...
Hi, In order to adjust the sound pitch a magnetic buzzer I thought using a PWM could be the right choice. Looking at the nrf5340dk device tree source I've found a pwmleds...
Following Setup:
1.) Building light-switch-app from original https://github.com/project-chip/connectedhomeip Repo for nRF5340 from command line with nRF SDK v2.1.0
2...
Hi,
We are close to going into a certification process but before we start we need to be sure we are not missing out on your recommendations with regards to EMC performance...
Hi,
I get the error like below on the Linux XFCE 64-bit platform (Pardus 21.2 distro latest version). It works fine on Windows but having a problem on linux. How can I solve...
