I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hello Team, We are currently building a circuit using nRF52833 QDAA QFN40 ( Configuration 5). We would like to know if there are dedicated pins to be configured for BOOT as...
Hi everyone,
I'm working on a Matter based project on the NRF52840 SoC. Since it's an Iot project project we need to reduce power consumption at it's minium for lifetime...
We're starting new medical research project where we have to send data at rate of around 4Mbps from the sensor array for a distance (omnidirectional) of around 2 meters. The...
Good day,
I am learning how to program NRF52832 chips using the NRF52 DK. I am using Segger embeddded v8.2 for the moment as I have not yet learnt how to use the NRF Connect...
Hi,
We have a project based on NRF52811_xxAA_REV1 running on multiple devices without any problem.
Nordic announced recently newer version of SoC (REV2, aka B0) and since...
I have been working on asset tracking v2 application code with thingy91 board, as it is not working. I have updated the modem firmware with latest one (thingy91_mfw-1.3.7_sdk...
Description: I am working with the USB mass storage example provided in github.com/.../mass The example works as expected when built and flashed using NCS v2.6. However, when...
Hello Nordic Team,
My application is cellular asset tracker type and we have design custom pcb using nRF9160 device.
I am using ncs SDK version: v2.8.0 and toolchain version...
I'm using Ozone 3.38, and SES 5.60a. I'm using the usbd_ble_uart example in nrf5SDK v16.0.0. I have other projects in production using this SDK version, but am using this...
Body:
Hello,
I have designed a custom board using the nRF52840 and flashed a simple LED blinking code. The LED does blink, but not according to the specified time intervals...
Sinds yesterday afternoon I seem to have lost access to nordic DevZone and nordic academy, while docs.nordicsemi.com works fine.
I have tested this on my office network...
Hello,
I am a student currently working on my diploma thesis, which is focused on the Nordic nRF52840. I have designed a custom board that is functioning well. At the moment...
I intend to extend the Secure DFU Service to perform some custom activities (including file transfer) from a Central to an nRF52832 device. During development it would be...
Hi, I'm using NRF21540-DK board to test hci_pwr_ctrl example. My FEM module can boost upto +21 dBm. How to correlate the tx power of radio peripheral(NRF52) and fem module...
