Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
Hello,
I am facing below AT_cmd errors after flashing my application to nRF9160 DK. Please support me how to resolve these errors asap as its blocking our product development...
Hi,
nRF Desktop v3.9.1 with Programmer v2.0.1 were almost functioning like the much older versions, but with the upgrade to v3.9.3 + v2.1.1 it is no longer possible to program...
Hello,
I have a running thread network now. Yay!
I am using a BMD-341 module from a old board as a Thread Sleeping end device. Getting great results.
I've flashed the...
Hello, we have made 50 cards with your microcontroller,out of the 50 cards there are 6 cards which consume about 10µA in sleep, while the others consume less than 1µA. Have...
Hi All,
We are using NRF52832 for our project.
We are using LED driver based on I2C protocol.
Do we have example code for I2C driver?
Please send some example/sample...
Hello,
I've installed nRF Connect for Desktop for Mac and from the UI using the Toolchain Manager I've installed nRF Connect SDK v1.8.0. After installing the extensions...
Hi,
I have been developing an application that reads sensor data (over SAADC and SPI) over an interval, serializes the data, and transmits the data over BLE_NUS to a companion...
Hi Nordic,
when I enable the Bluetooth configuration, the sensor trigger stop to work. when I comment the Bluetooth configuration, the sensor trigger back to work.
I recorded...
hi support team,
for nrf5 sdk ble_app_hid_mouse example, this example shows how to use swift pairing, it works. but I have one question for it, after I press reset button...
Hi, I'm trying to run samples provided by Nordic but I fail. My problem is west can not find my Jlink.
I can flash the chip (nrf52840 custom board) using nrfjprog
...
1. When I run the SDK routine provided by the official, ble_app_uart program, the circuit board acts as the peripheral , the protocol stack is pre-downloaded to the board...
Hi, I am new with nRF microcontrollers. I created a custom board that mounts the nRF52840 microcontroller. I made a firmware that uses BLE to exchange data and everything...
Hi,
I'm using nRF Connect SDK v1.7.1 with two nrf5430 DK. My goal is to evaluate the different security levels. For testing i send messages with the Nordic Uart service...
According to the AT command reference v1.7, the nRF9160 SIP modem firmware v1.3.1 added the %PERIODICSEARCHCONF command.
It does though not mention anything about the behavior...
We are evaluating OpenThread for a custom board with a BL654 from Laird, which contains an nRF52840. When running the OpenThread CLI sample from nRF Connect SDK 1.7.1 we are...
