Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I am thinking of using nRF5340 Audio on a development board.
The I2S-compatible IC on the headset side is an IC called AK4432VT.
The following settings are required to...
Hi,
We have a nrf5340 module on a custom PCB that is connected to a computer through use of a pcie header. This PCIE header allows USB communication to the module and supplies...
Hi,
In my project I need to send maximum bytes possible inside one package. When using the nrf connect app I can see that when reading the characteristic this works, but...
Hi . I have two questions about the PIPEs in Zephyr RTOS , especially regarding the correct use of the k _pipe _put and k _pipe _get functions :
1 ) In both functions ,...
Hi,
when I configure CONFIG_BT_SETTINGS=y as I want the device to remember the pairing parameters, the services defined with BT_GATT_SERVICE_DEFINE dissapear.
As far as...
Hi,
I use nrf52833 running ncsv2.6.0,
I trans v2.6.0\nrf\samples\bluetooth\central_hids to \ncs_v2.6.0\v2.6.0\zephyr\samples\subsys\usb\hid and now plus usb to nrfUSB...
How do I switch nrf52832 from a broadcaster to a peripheral with a service via a keystroke interrupt? After trying it out, I found that my problem was mainly: I didn't know...
Hi,
I'm using ble_app_att_mtu_throughput to communicate some data from a nRF52832 to another one. I reached my goal (1.4Mbps) but now I would know what the two board communicate...
Hi,
I'm trying to control nrf9160 SIP from stm32 MCU via AT Commands. Should I program on the nrf9160 the AT_CLIENT sample for this purpose or is not neccesary?
I'm trying...
Hello Team, We are currently working on a project for interfacing Larger TFT LCD display with Capacitive touch with nRF5340 Devkit board and SoC. As per the datasheet of the...
Dear Nordic,
I'm unable to register an nRF9161 device on the Verizon Thingspace IoT Network. They have a web UI which allows one to enter an IMEI, ICCID pair. When I enter...
We use custom board with NRF52840 and a MODBUS CO2 sensor. We are struggling with power consumption when the serial is enabled. The goal is to take measurements and then put...
// <i> NRF_FSTORAGE_SD uses the nrf_fstorage_sd backend implementation using the SoftDevice API. Use this if you have a SoftDevice present. // <i> NRF_FSTORAGE_NVMC uses the...