Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hi,
i develop my product ny ncs V2.6.0. in some case,i need store some user data to the flash,but i dont know how to read and write flash in cns sdk.if there is some samples...
Greetings.
Our team has encountered some difficulties in integrating nPM1300 into a new project. In the project we plan to use nPM1300 in conjunction with NRF52810. To develop...
* The nPM1300 LDSWSTATUS register @ Address offset: 0x4 doesn't contain values in the "Value" column.
* ID "E" occupies only one bit, but declares data on 4 devices:
...
We are planning to base a GATT and LE Audio design off of the latest nRF Connect SDK v2.6.1 and looking into Bluetooth certification. I have found the QDIDs for the Host and...
Hi, I try to launch west build command from a terminal.
I am first generating environnement variable as stated in this post :
Then I call it, and finally, I launch this...
Hello,
I am working on a custom board designed around the NRF52840. Currently the bootloader on the board is the same as the one on the NRF52840 DONGLE. It is out intentions...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
My goal is to achieve a data throughput...
We are connecting nrf boards to solar charged batteries for power consumption. We will be remotely deploying the boards on field. The boards are connected to sensors, from...
I'm going from v2.6.1 to v2.7.0; I'm using a thingy53. I'm getting a voltage error prior to boot.
[00:00:00.002,929] <err> voltage: setup: -134 *** Booting nRF Connect SDK...
Hello.
Wiring 1:
wiring 2:
Background to the case: We tested this with 2 different ppk2s and always got the same results. Our custom board works fine if we wire...
Hello,
I'm using nRF9160 as a HCI host and nRF52840 as HCI controller (nRF52840 config is based on HCI lpuart example). My application receives data over Bluetooth using...
Hi,
I evaluate MCUBOOT and trying to understand how it works. I am using a nRF52840DK. I have base my demo on this course ( Exercise 1 - DFU over UART - Nordic Developer...
Hi,
We would like to disable all wakeup sources before calling sys_poweroff. How to achieve this using Zephyr API? Pin configuration should remain as previously configured...
Hello,
I'm trying to enable the Power management for nRF9161 over nRF-Connect SDK2.5
the prj.conf has an entry of 'CONFIG_PM=y'
but it not accepted because we do not...