Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Hi, I'm currently in trouble with the sd_flash_write function. I've already a library using this function running on the nRF52832 with the S132 softdevice. But when a tries...
I want to use TWI to read the sensor data. When using the software TWI, I found that the communication takes a long time, which will greatly increase the battery consumption...
Hey,
I'm trying to put the nRF9160 into System Off mode and am getting a bus fault error when writing to the REGULATORS module. This is the error output:
***** BUS...
Hello everyone,
I try to import a project from Keil to SES,
I 'v read the instructions in this article.
Segger Embedded Studio - A Cross Platform IDE
Generally I have...
HI:
I'm using a cli routine from the SDK，and I register the callback function zcl_device_cb() with ZB_ZCL_REGISTER_DEVICE_CB()，But whatever message I receive does not go...
Hello community,
I successfully flashed assets_tracker code into board and configure in NB-IoT using Configure NRF SDK project in segger studio.
I used Vodafone SIM card...
Hi, I use nrf52832's uart with a simple driver, not "nrf_drv_uart", because I don't know how to use receive and transmit interruption with "nrf_drv_uart". the uart drive i...
Is there a supported way of doing an unsecure flash (the nRF is hardwired via UART to a secure processor) without rebooting?
The HW design the nRF is integrated with uses...
I am using the nRF52840 DK to read data from an IMU sensor (STm LSM9DS1 9DOF). Like most sensors, you transmit the register number first (on MOSI), then continue clocking...
Hi,
I am trying to develop models using the Specifications. I came across generic battery model which was using 24-bit values, time model which was using 15-bit and 40-bit...
Hi,
I've modified the SDCard example to write every 2 seconds 80 bytes to a SD Card. The SDCard is correctly mounted and the File is opened and kept open.
After several...
Hi,
Sorry if my english isn't perfect but I have a quick question and I could't find a good answer for what I'm looking for. I'm using a FPGA Arty S7 as a SPI master and...
Hello Nordic team
I have tested individual "record text" NFC example and buttonless dfu example with SDKv-15 and both example are working. Now I am trying to merge both...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hello Nordic Semiconductor Team,
I have a device which uses the buttonless dfu bootloader / app design. And now i have some issues with updating the firmware with iphones...
