I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hello there,
In my next project I need a data link similar to BLE classic (like the HC-05 module) and it needs to respond with an app API fast and push data rather then...
Hi,
I'm following "ble_app_uart_c" example and works very well with SDK 10.0.0. So now I want to communicate with HM-10 module, but this has one Tx/Rx Characteristic. Are...
Hello,
In my quest to monitor the activity of hundreds of nodes (directly addressable), I am facing quite an obstacle.
The small memory of the nrf52 (nice piece of hardware...
Hello How do I remove one server from mesh network? The client needs to recognize like a new device. I did try to use these functions without success on a event: nrf_mesh_node_config_clear...
I have successfully connected BT832 Module to NRF DK. I have erased BT832 and Falsh s132_nrf52_5.0.0_softdevice.Hex. using nRFgo Studio without any issues.
I have copy pasted...
Hi,
I'm trying to use the nrf52832 with a sdcard application in SDK_13. I based my code on the example provided and managed to get the sd card working without any problems...
The error "Unknown command add_pc_lint" appears when running the bootstrap command during setup. It looks like PC-Lint is an application for windows for software debugging...
Hello! I'm trying to find a list of boards that can be integrated into a circuit design which have already received compliance in the EU, UK and with the FCC. I found this...
Hello. i testing zigbee coordinaator example with zigbeee device. Device was joined to Zigbee coord/ network.
Couldn't i get device payload data in coordinator source code...
I have the UART configured using the standard boiler plate code, with flow control enabled, where the RTS output is assigned pin 5.
I have defined a GPIOTE pin 25 as an...
We are working on a solution that involves a central provisioner that provisions a MESH network of sensors that it subscribes to. We need to be able to replace this central...
Hi,
I am currently drawing up a schemtic involving the NRF52832 on Proteus 8.
I have been trying to find symbol, footprint, and 3D models of the NRF52832 online, however...
Hi!
We are using a custom bootloader for our device. Current version of this erases everything from 0x0 to bootloader start address, and then writes MBR + Softdevice ...
