The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I would like to test GPIOE APIs on nRF5340 develop board. But west build generated the following warning message.
Could I use nrfx_gpiote _xxx related APIs ( infocenter...
Hi,
I am not sure how to read from a characteristic which doesnt have notify property in them. I started looking into nrf_ble_gq_item_add() But I am not sure on what parameters...
hi
I am trying to get the nrf7002 dk working, however, when i try to provision the kit using the nrf wifi provisioner app i get an error saying " scanning error received...
Hello,
I'm working on nrf5340 audio bis gateway sample.
The NCS version I use is v2.2.0, I know it's a very old version, but for some reason I can't update to the latest...
| Host | <---- UART ----> | nRF52833 (central) | <-- BLE--> | nRF52833 (Target) |
I have a requirement where I hope to update the central's firmware image through the Host...
Hello,
With the latest version of the nRF5340 MDK I am getting the following linker errors (below), and don't understand why they should turning up.
Best regards
==...
Hello,
The documentation in the nRF7002 Product Specification rev 1.0 says that the P2P mode (Peer-to-peer) is supported (section 6). However in this ticket: https://devzone...
I need to use ADC in the project, and then I have configured ADC in overlay. The code is as follows
The same code can be measured normally in Zephyr's ADC example, but...
Hi,
I'm trying to use an nRF52840 dev kit as an I2S-to-USB microphone, but I've been running into a problem where the recorded audio is periodically unusable.
To debug...
Hey Everyone ... Looking for some ideas / help with crash involving nRF Sniffer v2 and Wireshark. Specifically I have an older White MacBook that I use for sniffing and nRF...
Hi,
I am using sdk 16.0 and I am already using 3 SPI Instances i.e. SPI1, SPI2, SPI3. I wanted to use SPI0 Instance also. How to use it?
If enable SPI0 in sdk_config I...
Hello
I was working on nrf9160-dk with assert_trakker_v2 application successfully connecting to nrf Cloud. There was no problem.
Today I started the day by deleting it...
From what I understand, the nPM1100 can work without the battery (i.e. no BAT connection).
Does the Nordic Thingy:53 come with the Li-Po battery separated or is it mounted...
Good afternoon everyone, how are you?
I'm using custom hardware, Nrf52833+Nrf21540, already reviewed by and tuned by Nordic. We are going to carry out the tests for product...
I need to work on single bank DFU from esp32 to nrf52833. I found a website with instructions on single bank configuration here: academy.nordicsemi.com/.../topic /exercise...