The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
In example "ble_app_hts" NRF_LOG_PROCESS don't work.
but in this "...\examples\peripheral\temperature" is workin good.
I didn't make any change in code.
Some ideas?
Dear
I need to make a BLE start network with bidirectional communication with up to 50 peripheral devices
And central and perapherals will be communicating with computer...
Hi,
I am having one nRF51822 to act as central and two nRF51822 to act as peripherals. I want the central to connect to both the peripherals and communicate with them. Is...
hello iam using nrf52832 and just started working is there any spp profile available for the same where i can send and receive the data btwn my smartphone and device wirelessly...
We are close to the manufacturing stage of our device and our beacons(based on nrf51 beacon reference design).
We are "virtually pairing" beacons with our device by entering...
I am currently working on a project that uses an nrf52832, SDK V11, and the S332 soft device. I am in the process of migrating to SDK 12.2.0. With the release of SDK 13, I...
Hi,
IOS example code
How to import CorePlot correctly in Xcode?
I always get this error message:
~/IOS-nRF-Toolbox-master/nRF
Toolbox/HRS/NORHRMViewController...
I am trying to use optiboot-ble with the nRF8001 and an atmega328p to allow application update over bluetooth. I have successfully compiled the bootloader and flashed it to...
Data sheets
Where is the data sheet for the
NRF51822 SoC located?
I am also looking for the ARM
Cortex-M0 data sheet, where is
this located?
I need to find...
When I try to program an example with nRF go Studio from the new SDK12 or SDK13(fresh download) I get the following error:
It does not show up if I don't program the...
Hi nordic guys,
I used the ble_app_hids_mouse demo to build my generic hid device(no mouse and keyboard) project.Now i modified the hids_init() function according my hid...
Hi !
I work for about a year with a nRF52832 custom board without problem and recently I add a bootloader (with success) on the firmware.
Now I can't connect through...
My application is based on ble_uart_app. I want to integrate the DTM so that the nRF51 will be in RF test mode when it receive command from UART. However, I found that the...
Hi all,
We're going to implement floating point agorithms on the new chip which has a FPU (cortex M4F). with the 64MHz system clock, how many flops can we have? I could not...
Hello.
I use nRF52 & mpu9250.
I want to use dmp.
But now it's not going well.
Now, there is no error,but fifo_count doesn't change after fifo_count became 512.
I...
