hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hello,
As per the requirement of my project I need to add a header file into one of the thingy:53 sample.
Can you please guide how can I add a new header file into it...
Hi ,
I am working on thingy53 and using ncs 1.9.1 I need to enable the BMI270 sensor and need the acceleration and gyroscope data from it. So for that, I primary using the...
Hello,
I am using the provisioner example to provision and configure all my sensor nodes in my project. My use case consists of around 60 sensor nodes. While provisioning...
Hi,
I moved my code on a second windows pc, checkout the code from git,download the same nordic sdk and softdevice version, same SES version but running on my board, the...
Devices: nrf52840 peripheral to nrf52833 central
background: We switched the mode from BLE_GAP_PHY_1MBPS, to BLE_GAP_PHY_CODED. The content of the advertisement data was...
Hello,
I want to use standalone logging for each file (/module)(/driver) of my program, therefore register different logging modules with different log levels each. Registering...
Hi,
I am attempting to configure a nRF52840 (packaged as Seeeduino XIAO Sense) for the popular printer software Klipper.
i have the following processor options and am...
Hello I'm trying to use GPIO pins as UART on the nRF 52 DK rather than the default UART pins. How do I change the pin configuration? I'm using nRF SDK version 17.1. 0
I now have two dk's, one as a master and the other as a slave. The slave sends data to the master, and the master forwards the data to the PC. That is, the piece of dk that...
We are seeing an issue with Android 13 on Samsung phones connecting to our device over BLE. After CONNECT_IND the phone will attempt to send a LL_FEATURE_REQ. It takes about...
Above is the code that im using.
Module - BT832x
Debugger - Segger J-link
IDE - Segger IDE
SDK - nRF5_SDK_17.0.2_d674dde (Downloaded from nordic website)
Program...
Hello Nordic Team,
I am facing an issue in my project that uses BLE and FreeRTOS. If I call nrf_sdh_enable_request () in main() before starting the task scheduler vTaskStartScheduler...
Hi,
I use 2 nrf52840 custom board, one is use a peripheral sensor with a lot of services and the other is used as a central with bt_shell_command.
Now i need to be able...
Hello Nordic support,
I am working on an application that works either with BLE or Zigbee and the protocol to be used is determined at application startup. Initially, my...
