You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
I've got a Thingy:91 plugged into my computer and can see its USB terminals (/dev/tty.usbmodem143101 and /dev/tty.usbmodem143104). I can also see the "ZEPHYR USB" volume and...
Good morning,
I am working on nRF52840 DK, using nRF5 SDK.
I am trying to communicate using SPI.
However, I found out that the function nrf_drv_spi_transfer took 10µs...
I am developing a solution with the nrf9160 that should use LTE and GPS at the same time. But unfortunately I am having some problems. Perhaps somebody from Nordic or the...
Hi everyone,
I am working on a project using nRF905 as an emitter and another Receiver(different than nRF905), the receiver is programmed in a way to perform some actions...
Hello Nordic Team,
I am having issues with the peripheral_uart firmware for the nRF52833.
1.I can use UART_init() or nrf_drv_uart_uninit() in nRF52-SDK to enable or...
hi all, 1. may i know how to get started of designing an AOA, mainly on how to send a CTE packet from TX to RX is there any code base or command that i can use? 2. i had noticed...
I am trying to establish a tunnel from ZigBee client to ZigBee server on nRF52840 using "nRF5 SDK for Thread and Zigbee v4.1.0".
Starting with the examples "examples\zigbee...
Hi everyone!
Challenge :
I'm trying to stream data from 9 nrf52832 (12 bytes each) to a computer, hopefully at 25 Hz at least (it seems more than realistic!).
Dream...
Hi !
I want to send simple HCI commands, such as reset, to the nRF5340 via UART. Therefore, I'm using the sample "hci_uart" available with nRF Connect SDK v1.5.0. I am sniffing...
It would be great to get some reassurance on this design. Is it ok for production i.e. is robust and within limits?
I am successfully driving an smd rgb led by sinking 2ma...
I am using the https fota, aws sample OK.
testd the aws certificate via Linux PC this way:
openssl s_client -connect kamacodeetrog.s3.us-east-2.amazonaws.com:443
now...
I'm trying to write the stripped down version of UART driver myself and having a few issues:
I enabled the UART, along with other registers as shown below
but when I...
on Ubuntu 20.04.2 LTS i have setup nRF connect SDK. When i try to configure segger Embedded studio. I am getting the error "create nordic project.py failed". I have connected...
The temperature sensor that i am using is analog. As mentioned above I have already gotten the temperature value using sd_temp_get().I also wish to send the values of voltage...
Hello all,
We are using Segger Embedded Studio (SES) v5.20 ,SDK v17.0.2 ,NRF52840DK board
The issue we are facing is we have a .msbl (kind of binary file)( file size 180KB...
