I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
I just both the board, and I can get the 4 LEDs and the NFC to work; I have followed all the instructions but unsure what is going on - and suggestions?
1.nrf9160 module abnormal reset, no abnormal reset log information, I would like to get modem related log submitted to you for further analysis, but I do not know how to use...
I use nrf5_SDK_for_Mesh_v420 on four nRF52 DK board, one is client, the other is server. But I fond, the light_switch_client example is used to control two server board, now...
Hello,
I am using the Light switch example for BLE meshing. I am trying to provision the nRF52832 with Raspberry Pi. I am unable to successfully provision because of the...
Hello!
I have created a function that cancels the connection by pressing and holding the button when Bluetooth is connected.
The use of this code allows the connection...
Hello,
I want to use FDS with bootloader but i get this error and i'am not sure how to manage it cleanly:
Linking target: _build/nrf52840_xxaa_s140.out
_build/nrf52840_xxaa_s140...
I have done a number of BLE projects using this chip. I am exploring two potential applications which would use the 2.4 GHz radio, transmit only, in a non-standard way. I...
Hello.
I've been asked to help develop an IoT device where GPS positioning and transmitting status via LTE-M/NB-IoT is central. So I've landed on the nRF9160 device, which...
I have a project bord which base on nrf9160, two buttons are set in the hardware circuit, corresponding to the pins of P26 and p15 respectively, and P07 is used as the interrupt...
It appears on the Thing91 reference board that the SIM_DET pin is used to drive the SIM mux control pin. Is that case? Is there more information on how to use this?
Is it acceptable to use the nrf52805's DEC4 pin as 1.3 V reference? I've connected the pin across a ~11 MOhm divider to to create a 0.12V reference for an op amp. I figured...
On SDK16.0.0 + Mesh SDK 4.1.0
I am using a Fanstel BT840X module that has an onboard Skyworks SKY66112 PA/LNA.
I followed the Infocenter guide along with an old example...
Hi, I'm having an apparent memory issue after increasing my PPI channel and GPIOTE allocation. Here's the basic setup:
nRF52840 with SoftDevice 6.1.0
SDK 15.3
I...
Hello,
We're intending to use the free flash region for two purposes: Flash Data Storage and DFU. The Flash Data Storage will be allocated a large number of pages (100...
