I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
My project has successfully debugged the communication of SPI_2, SPI_3 and UART_1. Now I need to debug the interface communication of I2C, when I turn on the macro switch...
Hi,
I need a way to have a concurrent connection (multi-peripheral), with whitelisting and bonding. Is there any example of this?
I found an example for multi-peripherals...
Hi!
I loaded up the LTE Sensor Gateway application on the 9160-DK, version 0.8.5. It crashes at the same point every time. I can see it connect to the cloud. When it attempts...
We would like our device to accept "just works" bonding for the first 2 minutes after power up in order to provide simplicity, but require mitm with oob after this to provide...
I have setup my new Thingy91 and got it connected to nrf Cloud. I can see environmental sensor data in the terminal window but it is asking me to update the modem firmware...
Hi, I am using timer capture function to get the current time when i get the interrupt on GPIO.
But it is not returning correct timer value in seconds (Example: for 2-3sec...
Ok so this is an interesting one.
When I got a new PCB with a MDBT42Q module containing NRF52832 I flashed it for the first time (program and softdevice) all the code works...
Hi, I have started development on nrf52840 .
I want to use BLE as a Peripheral . Can you please suggest me which example I can use for sending characteristics and add my...
Hi everyone, I have questions like this: I'm using experimental_lpn example when I want to connect to the friend node when I get request timeout. As far as I know when the...
We're thinking of attaching a battery in the manufacturing process but they may not be programmed right away. Do empty nRF52 modules go into sleep mode when there is no program...
Hi
how to connect one peripheral to two central and after connection established sent the data to both central?
I am using nrf52, soft device 132 .
i am able to make...
Hi!
The nrf5340 PDK I've purchased does not have a mounted "nRF USB" (J3) port, only the debug (J2) port.
Is it possible to do raw USB communication with the USBD driver...
Dear Sir.
I am using the Timer of nRF916 .
In a simple project the timer is working fine ( see attached code ).
A buzzer is connected to PWM output pin 12.
I can...
Dear Sir.
Attached a code .
It takes about 20 seconds from power on until the Blue Led is On.
The timing of the Blue Led is about 2 sec , as in the code.
Commenting...
Hello
I use sdk v17 and nRF52DK. I want to use mpu6050 sensor in the example of ble_app_uart. SDK provides a driver for mpu6050, but I am not good enough to use it.
https...
