I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
I know that the SoftDevice has support for controlling a frontend with TX and RX signals.
However, our radio module uses a Skyworks SE2431L frontend with the control signals...
When using the script interactive_pyaci.py together with ipython and the serial example, I observe a strange formatting in the command window, because the "In [..]" is often...
SDK is nRF5_SDK_13.1.0_7ca7556.
Example is ble_ant_app_hrm.
Softdevice is S332.
The example can connect android but can not connect iphone.
Iphone 7 and ios is 10...
Disconnection of the peripheral is done without enabling another connection, the only way is to reset the module.
It happens sometimes after 5 min up to 1-2 hours.
If...
Hi all,
I'm working on an application that requires BLE. I've recently upgraded my project from sdk 14.0 to 15.2 in order to deal with some problems that I ran into with...
Hi,
I am trying to configure the nRF52810 clock setup to accept the LF CLK source from a pin on stm32l4xx on a custom board without much luck. My setup works correctly if...
Hello. I move ble_app_uart with a combination of nRF 52840-DK and SDK v 15.2.0. Using UART 0 or UARTE 0 confirms that it can communicate with nRF 52832 on the Central side...
Hi,
I am trying to understand the current consumption of a very simple BLE application running on the nRF52832 DK. For my final use case, I'd like to reduce the peak current...
Our project uses a Raspberry Pi compute module 3 connected via UART to 2 nRF51822. I'll go through what is working and than describe the issues I'm having
What's going...
Hi, I'm using ble_app_hrs_freertos from SDK 15.2 on PCA10056. I noticed that logs stop working (RTT) when I increase configTOTAL_HEAP_SIZE to 64k. I tried play with various...
I've got myself one an E73-2G4M04S1A board containing an nRF52810 chip for evaluation. I've setup an Raspberry Pi 1 rev2.0 with OpenOCD using this guide and wired it up according...
Hello,
i have bought 3 modules from Rigado (BMD-330-A-R) with a nRF52810 SoC, is it possible to flash it with an Raspberry Pi? I read that SWD is possible by its SPI-Interface...
We are in progrees of developing a wearable device using NRF52832 with BLE. The problem is, we have quite a few chips dead after several times of rewriting. The dead chips...
Hi,
I tried adding PWM for turning on/off the LED's on the DK for the Enocean switch example. It worked well.
I tried to perform dimming on the switch example by restricting...
