I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Chip: NRF51822
Per the documentation the band gap voltage is 1.2V however on my board when I apply the voltage 1.5V to AIN2 i read the following value from the ADC: 209...
I am completing a schematic using the nRF51822 part. I will be supplying the part with a 3.3V supply. I will use one of the ADC inputs to sense battery voltage (up to 10v...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
I was using nRF Master Controller app on Samsung S4 to connect to my Ble device. However, after connected a while, the device will be disconnected automatically while I was...
I'm getting started and have an overwhelming amount of stuff downloaded which I'm trying to make sense of.
Which of the examples in the nrf51 SDK use the Softdevice and...
Hi,
I'm using a NRF8001 shield with an Arduino Leonardo, everything connection wise seems to be working. I'm using the "ble_my_project_template" and uploading various services...
I install the j link driver for mac(4.78k),connect the ek,but can't recognition it:
Sens-Macbook:~ sen$ JLinkExe -if SWD -device nRF51822
SEGGER J-Link Commander V4.78k...
I'm usually cleaning out the older manuals when downloading new ones from the web site. Unfortunately the new EK user guide 1.2 doesn't show how to connect the nrf51822 UART...
I would like to use an idle loop for non critical tasks. Is there any way this can be done with the scheduler implementation? I don't want this to be time based, I just want...
I have worked with nrf24l01+ devices. In my project include single PRX with 100 PTX. Objective of this project is all PTX send packet to one common PRX device & PRX send ack...
I have the simple UART example working with the nRFgo motherboard laid out as described in the SDK docs, with 2p connectors on the RS-232 P15 and the SDA and SCL pins of the...
Hi All,
I'm just starting to use the 51422 DK and I do as the nRF51422_Developer_Kit_User_Guide,I have flashed the broadcast_tx of the ant_broadcast project in SDK and...
After I download NRF51822_0.9.0.HEX in PCA10001 v2.1, but the MCP cannot work. Anyway, PCA10000 is working fine. Do you have any solution about this? Thanks.
