Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hello! I am using nRF Connect SDK 2.6.0v. I want to enter the device into deep sleep mode when i press the button 2 sec When Next time I press the button 2 sec, wake up from...
Hi!
This question has been asked before in various forms, but none of the answers I've seen will work;
Is there a way to get any callback before or after a BLE Advertisement...
Hi all,
i am using NCS 2.4.0
I have a question is there any possible that i can use double slot to update firmware over BLE FOTA?
I already look at the website below...
Hello, I am currently working on a custom board that contains the E73-2G4M08S1C module. This module contains the nRF52840 chip. My goal is to exit System On periodically every...
How to create multiple BLE connections, one just advertising and another allowing connections with different names with the nrf Connect SDK in the peripheral_HR example?
Hello Nordic team,
I am using nPM1300 and nRF5340 in my custom board. I am using also Renata ICP621333PA-01 battery in my design. In order to prolong the battery life, I...
I am using a Mikroe development board with the nRF9160 to establish an LTE connection and send MQTT messages to a broker. The application successfully connects to the network...
I have used the nRF52832 on a few dozen projects, usually at 3.3V etc. On this project I have it at 1.8V, which may be related, but spec is 1.7V min, and the 1.8V supply is...
Hi Noridic team,
I am developing with nRF5340, and I added the following configuration to the prj file:
CONFIG_SPI_NOR_INIT_PRIORITY=75
However, I got the following...
Hi, I cannot compile because of the error below. Thank you in advance for any help.
I have updated the toolchain and sdk recently. Tried also with 2.6.1 and 2.7.0, the same...
I am porting the LoRa Basic Modem to the nRF52832 , using the nRF5 SDK and Segger Embedded Studio (SES) . In my application, I am using SoftDevice and implementing FOTA ....
Hi,
We recently updated our NRF Connect SDK from v2.2.0 to v2.7.0.
After porting to the SDK v2.7.0 we are not able to build the project with DFU enabled. We get below...
What is the best method to ensure the nRF9160 LTE functions on a PCB during assembly with minimal test equipment? Our thoughts were to search for available networks using...
We want use NRF5340 to do le audio application. We got the demo from your website, and find the audio demo, but the min sample rate is 32khz can be set, we want to use 8K...
