Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
I have been trying to measure the PER between two nRF52840 DKs using BLE. To do so, I am using BLE Direct Test Mode to start a transmission on a 52840 DK and another development...
Hi Nordic Team, I'm using the nrf52833 controller with nrf Connect SDK v1.9.1. I wanted to enable the watchdog in MCUBOOT starting main.c file and disable it just after giving...
I am developing a BLE DF project using the nRF52833 DK, and I am currently confused about the antenna location on my DK. I have not found any markings like "ANT" or "TX" on...
i have two toolchains inside my ncs directory. i am trying to build my main program using west build and the west exe that i am using is the one from the right toolchain....
Hi,
I'm doing nrf52833's spi function.I want to use hardware slice selection instead of pulling the gpio pin, and the reference manual has the register IFTIMING.CSNDUR....
Our custom development board uses an nrf52840 chip together with attached sensors. The data from sensors are stored in sd card. For this purpose, the Zephyr fs library is...
Here is a stacktrace from a device I got using the nRF Connect mobile app on Android.
nRF Connect, 2024-05-11 Device Name (A4:XX:XX:XX:XX:7C) D 13:40:23.035 [Callback] Connection...
I'm trying to setup a I2S module by referring the I2S module given in the nrf5340-audio application. This is my audio_i2s.c file.
Now when I'm building this...
What should I change to run the hci_lpuart sample with UART asynchronous API instead of the using the interrupt driven one? I have already changed the source file on the sample...
I was able to run blinky successfully on my customized nrf5340 board, but it doesn't respond to writing matter related code, there is no output from the RTT, I refer to the...
Hello,
I am reaching out regarding some challenges I've encountered with SPI communication on the nRF7002DK when interfacing with the ETH Wiz Click | Mikroe module and a...
Hello,
I am a student and new programmer and got the Thingy:91 for a project at Uni. I went through the getting Started guides and now I am at the point, where I downloaded...
I tried adapting the blinky sample project to work with a custom board. After an hour or two I was able to define the GPIOs of my schematic including I2C with the device tree...
