I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
I have a SPI Master and a SPI Slave. The Master will randomly pull data over SPI from the Slave. The slave will randomly generate events that result in data to be sent to...
I am using SDK version 17.0.2. The example code uses SPI.
The following changes have been made to the pin settings.
Questions
1. Pin behavior is strange.
...
Hello, Support team.
Our boards do SPI communication to read sensor data.
Basically It works well. I checked that It operates more than 5 hours.
But only one board...
Hi,
I have the following initialization for advertising:
The name consists of an acronym od three letters and a underscore e,g, XXX_ and a six digit ID. Like XXX_12E124...
Hi,
Is it possible to add four pairs of resistors between the debug signal lines and the connector as shown in the figure below.
Would such a connection not impair the...
The Google Fast Pair Service has recently been included in a number of Bluetooth peripherals (Headphones, fitness trackers, etc.) and has been getting rave reviews.
Has...
I am able to download simple blinky program on my custom board. It is working fine. Custom board is interfaced with nRF52-DK through P19. I am using embedded studio as IDE...
Hi, on nRF5340 I want to capture accurate timing of external events. I need a kind of real-time capture module to read the time period of a pulse train generated by a rotating...
Have a few questions about ble_app_uart example.
From the way I see it, it sets uart_event_handle as the callback, and every time there's an "event" that takes place...
Hello All,
Method 1: I am writing a test application to read the ADC data at a specific intervals(10 samples for every 5ms interval for every 50sec). I am using blocking...
Hi,
We are implementing a synchronous light flashing of multiple devices, so:
1) Can we get a millisecond level (< 10ms) time synchronization by parsing the Link Layer...
Hi, all
I added a scanning module to the example 'ble_app_uart.c', so each one works well.
What I want to do is advertising and connect at the same time while connected...
What is the best practise for multichannel SAADC conversion in ultra low power devices? For example I have to measured 4 channel in interval 250ms. Below what I try:
...
Hi, Dear Nordic & all:
when I run the ble_app_hids_keyboard example in nrf52820(SDK17.0.2), I meet a question:
1、Frist I use my iphone connect ble device and pair success...
Dear Nordic:
so I want to know In nRF52 serials chips, How much HFCLK CONTROLLER ppm is the frequency offset distribution and production FT control range? Do you have any...
