hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
I saw a description about on-the-fly CCM mode decryption in the nRF54L10 datasheet, but the Configuration section of CCM00 states that it does not support on-the-fly decryption...
I would like to know about the Mesh model.
Light Lightness、
Light CTL、
Light HSL Setup、
Light Control
Are there no configuration components for any of the above...
Hey,
To program the nRF54L15 EVK, is there some dedicated program tool needed?
From EVK package ordered online, there is only USB cable inside. Can I assume the USB cable...
SDK: 3.0, nRF54L15
I have modified the clusters using ZAP tool (west zap-gui). When I tried to built, I get the below error:
1. I used Matter door lock sample and the...
Hi I am starting with nRF9160. I build and program "nrf91_simple_tracker," but while running, I got the following terminal output:
I am using nRF Connect SDK v2.7.0 with...
I'm developing a solution using nrF54L15 that needs to receive packets from existing legacy RF devices in the field that cannot be modified.
Required RF Parameters:
...
Hi team,
I am using ncs2.6.1 ( github - install from VS Code ) , toolchain 3.0.2 ( previously used 2.6.1), My DK works great standalone also here is the view from nrf-connect...
Hi,
I am planning to get the PPK2 fabricated and assembled using the HW files available for PPK2.
Just wanted to check will I have issues loading FW on it since I don...
Hi all,
I’m working with an nRF52833 using SDK 2.8 and trying to enable DCDC mode to reduce current consumption.
I tried adding:
CONFIG_BOARD_ENABLE_DCDC=y but I got...
When developing a keyboard peripheral using the nRF5 SDK keyboard example, how can I determine whether the connected host device is a Mac, Windows PC, or Android phone?（NRF52833...
Hi, I am working on a channel sounding trilateration system using an initiator and three reflectors. When I was testing with six reflectors I couldn't help but notice the...
Hi all,
I need to use the SPI3M interface and following various example I implemented the following code on the nRF52840 with SDK 3.0.2
Whenever I configure the SPI to...
Hello - Just download and installed NRF Connect for Desktop 5.2.0 on Windows 10. Trying to Quick Connect to new PPK2 1.1.1.
When I plug in USB Quick Connect sees the PPK...
Hello,
we were using the mcumr_flutter 0.4.2 library to Update our NRF54L10 over the air with an app. This was working fine using the nRF Connect SDK Toolchain v2.9.0. However...
Hello,
I'd like to have the gcc linker calculate a checksum over a specific address range (defined in .ld file) and store that checksum at a specific address (defined...
