It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi
I'm trying to use the nRF52840 DK debug out to program/flash an external nRF52840 IC that runs at 1.8V logic level. According to the manual, the DK is running at 3V...
When running our hardware using the J-Link debug in connector on the dev kit, BT is fully functional. But when we try to run using the very same power source (ie, the dev...
Hi all,
I'm developing a custom board that is equipped with a nRF24L01+ (directly soldered on my PCB, no breakout). The board is equipped with a PIC32, that controls also...
SDK 15.2
port_cmsis_systick.c
nrf_drv_clock_lfclk_request is part of the legacy drivers that will eventually be removed?
Does this mean for FreeRTOS I need to keep...
Hello,
I want to set the nrf24le1 module into register retention mode with timers ON but clock source from XOSC32K. I need this power saving code in my project. Also can...
Hi,
I am using adafruit Bluefruit BLE SNIFFER. My question is whether it is required to use jLink along with it to connect to it via USB. Also, I have a question can I sniff...
sdk5 15.2's app_timer.h at line 61 says:
* @details Use the USE_SCHEDULER parameter of the APP_TIMER_INIT() macro to select if the * @ref app_scheduler should be used or...
I am trying to read hts221 and ccs811 sensors from thingy and want to make the data available on UART(P0.02,P0.03).
I have tested the uart code and able to print data -...
Hi all,
I am trying to configure the LPCOMP module of the nrf52832 using registers directly, that is, without using the already generic functions that come with the sde...
Hello
I have two similar (as their producer says) boards. Both nRF52832. The main difference is in modems used for external data transmission.
SDK 15.0.0
SD 132
I...
I have an application using mesh SDK 2.1.1 that is working. I am migrating to V2.2.0. In my current code I use nrf_mesh_opt_set() to enable and disable a relay feature. I...
Hi,
Can nRF Sniffer v2.x software flashed in nRF52832 used along with wireshark sniff all BT 4.0,4.1,4.2,5.0 packets?
Please confirm so that we can proceed to buy the...
Hi there,
The DFU Nordic samples have a 4K "MBR Params" page, located in the last 4K of flash. e.g., the linker file has:
MBR_PARAMS_PAGE (rw) : ORIGIN = 0x0007E000...
Hi,
I need to minimize the power consumption.
For this reason when my device is in advertising the peripherals:
TWI
hight frequency clock
external interrupt on...
SDK version 15
I'm adding two more BLE services to my working custom one. And ran into some advertising issues. This is what's spitted out from GDB.
ble_advertising_init...
