I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
I am designing an nrf52 based device running at 1.8V. To debug the device I was planning to use debug out option of the nrf52 preview DK. However, I just find that, the debug...
I'm trying to follow the code from one of your examples, specifically ble_beacon in SDK 8.0 and eventually I get to a point where I'm not sure what's going on so I figured...
Hello,
I have question. I using examples with nRF51-ble-peripheral-bond-handling with bls_service (PCA10028) and i have problem with unnecessary connection. I want that my...
I'm referring this blog on getting started with nRF51822 and in this same blog, there is a link to a video by Nordic on Introduction to Bluetooth Smart and after watching...
I have two STM8s105 MCUs and two NRF24L01+ modules. Set one as transmitter:
CONFIG: 0x3A
EN_AA: 0x00
EN_RXADDR: 0x03
SETUP_AW: 0x03
SETUP_RETR: 0x00
RF_CH: 0x00...
Hi
I used the boot loader example successfully on the nrf51DK board.
Now I want to use it on my custom board. So I recompiled the boot loader code, with 1 difference:...
I don’t fully understand the nRF51 event NRF_RADIO->END. NRF_RADIO->END identifies the completion of a packet transmission or reception. My question is what triggers NRF_RADIO...
We have a project that involves both battery-powered 'slave' devices and a mains-powered 'master' device (which needs to support multiple slaves and support WiFi). We are...
Hi,
imagine that I have a proprietary characteristic that allows only READ operation (from a smartphone for example) that expose an internal value in my application.
I...
Hi,
I'm using nrf51822 and SDK 6.1.
devzone.nordicsemi.com/.../
I learned how to store data with using pstorage library.
but I can't register block more than 1024...
my chip : NRF51822 (256kb)
SDK : 6.1
Hi.
devzone.nordicsemi.com/.../
according to this example code, I could have stored data and it works great.
but problem...
I want to update the bootloader inside nRF51422 using iPhone.
Updating applications hasn't been any problem.
Following the same procedure but I cannot convert bootloader...
Hello,
I received a reminder to aswer to the Nordic Semiconductor Customer Satisfaction Survey. Unfortunatelly, I can not reply, because there are questions I simply can...
Hi All,
The timer count value reading is not working.
static void timer2_init(void)
{
/* Start 16 MHz crystal oscillator */
NRF_CLOCK->EVENTS_HFCLKSTARTED = 0;...
